Related Manuals for Case IH 3230
Summary of Contents for Case IH 3230
- Page 1 Case IH 3230/3240/3320/ 3330/3340 & 4420/4430/ 4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual P/N 016-0230-129 Rev. A 01/17 E28458 Copyright 2017...
- Page 2 Disclaimer While every effort has been made to ensure the accuracy of this document, Raven Industries assumes no responsibility for omissions and errors. Nor is any liability assumed for damages resulting from the use of information contained herein. Raven Industries shall not be responsible or liable for incidental or consequential damages or a loss of anticipated benefits or profits, work stoppage or loss, or impairment of data arising out of the use, or inability to use, this system or any of its components.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Important Safety Information ................1 Hydraulic ........................... 2 General ....................................... 2 Instructions for Hose Routing ............................2 Electrical ............................ 3 General ....................................... 3 Instructions for Wire Routing ............................3 Chapter 2 Introduction......................5 Introduction ..........................5 Preparing for Installation ...................... - Page 4 Connect the Harness to the Power/CAN Controls ..............35 90’-100’ Booms ..................................35 120’ bOOMS ..................................36 Chapter 7 Replacement Parts....................39 Valve ............................39 Sensors ..........................40 Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 5: Important Safety Information
I MPORTANT SAFETY CHAPTER C H A P T E R 1 INFORMATION NOTICE Read this manual and the operation and safety instructions included with your implement and/or controller carefully before installing the AutoBoom® system. • Follow all safety information presented within this manual. •... -
Page 6: Hydraulic
• Pulleys, gears, sprockets • Deflection and backlash of belts and chains • Adjustment zones of adjustable brackets • Changes of position in steering and suspension systems Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 7: Electrical
IMPORTANT SAFETY INFORMATION • Moving linkages, cylinders, articulation joints, attachments • Ground engaging components For hose sections that move during machine operation: • Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or rubbing, especially in articulation and pivot points •... - Page 8 Remove visible surface water from components, connections, or seals using pressurized air or an aerosol electrical component cleaning agent. allow components to dry completely before reconnecting cables. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 9: Chapter 2 Introduction
Congratulations on your purchase of the Raven AutoBoom system! This system is designed to provide automated boom height adjustment for agricultural equipment. This manual applies to the following machines. MAKE: Case IH MODEL: 3230, 3240, 3320, 3330, 3340, 4420, 4430, and 4440 YEAR: 2010 & Newer FIGURE 1. Case IH 4420 PREPARING FOR INSTALLATION Before installing AutoBoom, park the machine where the ground is level, clean, and dry. -
Page 10: Recommendations
This manual may reference the following types of hydraulic fittings: • SAE O-ring fittings • ORFS (O-Ring Face Seal) fittings • JIC fittings SAE O-ring fitting JIC fitting ORFS fitting Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 11: Updates
To serve you best, please send an email with the following information to techwriting@ravenind.com -Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual -P/N 016-0230-129 Rev. A -Any comments or feedback (include chapter or page numbers if applicable). - Page 12 Cable - AutoBoom Harness 115-0230-073 U-Bolt - 2-1/16” W x 3” L x 3/8” Thread 107-0171-609 U-Bolt - 3-9/16” W x 4” L x 3/8” Thread 107-0172-471 Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 13: Autoboom Installation Kit - 120' Booms
Item Description Part Number Qty. Manual - ISO AutoBoom for Case IH Not Pictured 016-0130-079 Calibration and Operation Manual - Case IH 3230/3240 and 3320/ Not Pictured 3330/3340/4420/4430/4440, Model Year 016-0230-129 2010 & Newer AutoBoom Installation Valve - AutoBoom Hydraulic 063-0131-124... - Page 14 U-Bolt - 3-9/16” W x 4” L x 3/8” Thread 107-0172-471 U-Bolt - 2-9/16” W x 3-1/2” L x 3/8” 107-0171-616 Thread Bolt - 5/816”-18 x 7/8” Hex 311-0052-104 Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 15: Hydraulic Installation Kit
INTRODUCTION TABLE 2. UltraGlide Installation Kit (P/N 117-0232-129) Picture Item Description Part Number Qty. Bolt - 3/8”-16 UNC x 1-1/4” Hex 311-0054-081 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 Washer - 5/816” Zinc Lock 313-1000-019 HYDRAULIC INSTALLATION KIT TABLE 3. Hydraulic Kit (P/N 117-0134-075) Picture Item Description Part Number... -
Page 16: Optional Inner Ultrasonic Sensor Installation Kit
Sensor - Right Ultrasonic 063-0130-014 Bracket - Sensor Mounting 107-0172-501 Cable - 40’ Ultrasonic Sensor Extension 115-0171-602 U-Bolt - 2-1/16” W x 3” L x 3/8” Thread 107-0171-609 Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 17: Optional Wheel Kit - 90'-100' Booms
INTRODUCTION TABLE 4. Inner Ultrasonic Installation Kit (P/N 117-0137-026) Picture Item Description Part Number Qty. Bolt - 3/8”-16 UNC x 1-1/4” Hex 311-0054-081 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 OPTIONAL WHEEL KIT - 90’-100’ BOOMS TABLE 5. Optional Wheel Kit (P/N 117-0134-006) Picture Item Description Part Number... -
Page 18: Optional Wheel Kit - 120' Booms
Bracket - CaseIH 120’ Boom Weldment 116-0159-680 Wheel 322-0131-008 U-Bolt - 2-1/16” W x 3” L x 3/8” Thread 107-0171-609 Bolt - 1/2”-13 x 1-1/2” Stainless Steel Hex 311-0058-186 Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... - Page 19 INTRODUCTION TABLE 6. Optional Wheel Kit (P/N 117-0133-075) Picture Item Description Part Number Qty. Nut - 1/2”-13 Zinc Hex 312-1001-043 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 P/N 016-0230-129 Rev. A...
- Page 20 HAPTER Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 21: Hydraulic System Installation
H YDRAULIC SYSTEM CHAPTER C H A P T E R 3 INSTALLATION WARNING The machine must remain stationary and switched off, with the booms unfolded and supported, during installation or maintenance. CAUTION When installing AutoBoom hydraulics or performing diagnostics, maintenance, or routine service, ensure precautions are taken to prevent any foreign material from being introduced into the machine’s hydraulic system. -
Page 22: Mount The Autoboom Valve
1. Secure the UltraGlide AutoBoom valve (P/N 063-0131-124) to the mounting bracket (P/N 107-0171-802) using four 5/16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 23: Install The Pressure And Tank Hoses
HYDRAULIC SYSTEM INSTALLATION FIGURE 2. AutoBoom Valve Mounted on the Sprayer 2. Secure the mounting bracket to the machine’s center rack using two 2-9/16” W x 3-1/2” L x 3/8” thread U-bolts (P/N 107-0171-616) and four 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). NOTE: Mount the AutoBoom valve so that Port P is facing up and LC and RC Ports are facing the center of the machine. -
Page 24: Install The Left And Right Cylinder Hoses
FIGURE 4. Left and Right Cylinder Hoses Installed 1. Trace the machine’s left and right cylinder tilt hoses from the rod-end of the tilt cylinders to the machine’s hydraulic valve. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 25: Install The Left And Right Down Hoses
HYDRAULIC SYSTEM INSTALLATION 2. Disconnect the machine’s left and right cylinder tilt hoses from the machine’s hydraulic valve. 3. Install -6 ORFS M/M/F swivel run tee adapter fittings (P/N 333-0012-069) in the tilt hose ports of the machine’s hydraulic block. 4. - Page 26 HAPTER 9. Connect the straight end of the installed hydraulic hose to the installed fitting in Port LF CYL RTN of the AutoBoom valve. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 27: Ultraglide Hydraulic Schematic
HYDRAULIC SYSTEM INSTALLATION ULTRAGLIDE HYDRAULIC SCHEMATIC P/N 016-0230-129 Rev. A... - Page 28 HAPTER Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 29: Chapter 4 Sensor Installation
S ENSOR INSTALLATION CHAPTER C H A P T E R 4 NOTE: For optimal system performance, Raven Industries recommends a five sensor system configuration. If the machine is not already equipped with inner sensors, a dual system upgrade kit (P/N 117-0137-026) is required to complete the five sensor configuration. -
Page 30: Mount The Boom Sensors
3. Mount the right boom sensor assembly on the front of the right-outer boom section using two 2-1/16” W x 3” L x 3/8” thread U-bolts (P/N 107-0171-609) and four 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 31: Mount The Center Sensor
SENSOR INSTALLATION FIGURE 4. Left Inner Boom Sensor Installed 4. If optional inner boom sensors are being installed, repeat the steps above to mount the inner boom sensors to the front of the boom. NOTE: Ensure that the sensor does not contact the inner boom section when the boom is folded in toward the cab. - Page 32 4. Repeat the steps above to connect the remaining sensor cables. NOTE: The sensor cables will be connected to the AutoBoom system in the wiring phase of installation. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
- Page 33 SENSOR INSTALLATION P/N 016-0230-129 Rev. A...
- Page 34 HAPTER Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 35: Gauge Wheel Installation - Optional
G AUGE WHEEL INSTALLATION - CHAPTER C H A P T E R 5 OPTIONAL GAUGE WHEEL MOUNTING LOCATIONS Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms. -
Page 36: 120' Booms
8. Secure the gauge wheel assembly in the wheel mounting bracket by installing two 1/2”-13 x 1-1/2” SS hex bolts (P/N 311-0058-186) and two 1/2”-13 zinc hex nuts (P/N 312-1001-043). 9. Repeat the steps above to install the right wheel. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 37: Wiring Installation
W IRING INSTALLATION CHAPTER C H A P T E R 6 WIRING CONNECTIONS CAUTION Always connect the power cable as the last step in the wiring process and verify that the power leads are connected with the correct polarity. Reversing power leads can cause severe damage to the equipment. -
Page 38: Connect The Harness To The Autoboom Valve
5. If optional inside boom sensors are installed, repeat the steps above to connect the harness to the inner boom sensors. 6. Locate the CENTER SENSOR cable and connect it directly to the center sensor. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... -
Page 39: Connect The Harness To The Power/Can Controls
WIRING INSTALLATION CONNECT THE HARNESS TO THE POWER/CAN CONTROLS 90’-100’ BOOMS FIGURE 3. AutoBoom Harness Cable Installed 1. Locate the machine’s harness cable bulkhead on the center boom section, near the pressure transducers on the sprayline. 2. Disconnect the machine’s cable from the bulkhead connector. 3. -
Page 40: 120' Booms
FIGURE 6. Machine’s CAN and Aux Power Connections AUX POWER CAN Terminator Removed and AutoBoom Harness Connected 2. Disconnect the machine’s CAN terminator from the machine’s harness. Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... - Page 41 WIRING INSTALLATION FIGURE 7. Machine’s CAN Terminator Connected to AutoBoom Harness Cable 3. Connect the machine’s CAN terminator to the harness cable’s (P/N 115-0230-032) CAN connection. 4. Connect the AutoBoom harness cable’s CAN connection to the open CAN connection on the machine’s harness.
- Page 42 HAPTER Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
-
Page 43: Chapter 7 Replacement Parts
R EPLACEMENT PARTS CHAPTER C H A P T E R 7 This section contains replacement part diagrams and listings for the AutoBoom system. Please refer to these diagrams when calling to request replacement parts. VALVE P/N 016-0230-129 Rev. A... -
Page 44: Sensors
HAPTER SENSORS Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual... - Page 45 Index Electrical Safety Preparing for Installation Gauge Wheel Installation Replacement Parts Gauge Wheel Mounting Locations Sensors Mounting the Gauge Wheels Valve 120’ Booms 32 90’-100’ Booms 31 Sensor Installation Connecting the Sensor Cables Mounting the Center Sensor Hydraulic Safety Hydraulic System Installing Fittings on the AutoBoom Valve Installing the Left and Right Cylinder Hoses Installing the Left and Right Down Hoses...
- Page 46 Index Case IH 3230/3240/3320/3330/3340 & 4420/4430/4440, Model Year 2010 & Newer ISO AutoBoom® Installation Manual...
- Page 47 Limited Warranty What Does this Warranty Cover? This warranty covers all defects in workmanship or materials in your Raven Applied Technology Division product under normal use, maintenance, and service when used for intended purpose. How Long is the Coverage Period? Raven Applied Technology products are covered by this warranty for 12 months from the date of retail sale.
- Page 48 Extended Warranty What Does this Warranty Cover? This warranty covers all defects in workmanship or materials in your Raven Applied Technology Division product under normal use, maintenance, and service when used for intended purpose. Do I Need to Register My Product to Qualify for the Extended Warranty? Yes.