Related Manuals for CAS Talline
Summary of Contents for CAS Talline
- Page 1 Talline s a l t w a t e r c h l o r I n a t o r INSTALLATION & OPERATING INSTRUCTIONS MODEL: TL RANGE...
-
Page 2: Table Of Contents
Talline Designed and manufactured in Australia TABLE OF CONTENTS Important Warnings and Safety Instruc ons....................3 1.1 Important Warnings........................3 1.2 Important Safety Instruc ons.....................3 2. General Overview............................4 2.1 Recommenda ons and Helpful Hints..................4 2.2 Contents .............................4 2.3 Tools Needed..........................4 Pool Prepara on............................5 Power Pack &... -
Page 3: Important Warnings And Safety Instruc Ons
1. IMPORTANT WARNINGS & SAFETY INSTRUCTIONS 1.1 Important Warnings This manual contains important informa on about the installa on, opera on and safe use of this product. This informa on should be given to the owner and/or operator of this equipment. When installing and using this electrical equipment, basic safety precau ons should always be followed. -
Page 4: General Overview
The Talline range is a reverse polarity model known as TL, which is a reversing design and automatically changes direction every 5 – 10hrs (depending on your se ng). This change of polarity causes the calcium to dislodge and keep the cell plates clean. -
Page 5: Pool Prepara On
3. POOL PREPARATION Before operating your Talline™ unit please read the following: • Check your salt levels with your local pool professional before installing your unit. • Salt levels should ideally be 3 00 – 4 500ppm and no more than 000ppm. -
Page 6: Power Pack & Cell Electrode Installa On
4. POWER PACK & CELL ELECTRODE INSTALLATION 4.1 Power Pack Installa on • The Talline™ Power Pack has a Ingress Protection Range of IP23 enabling it to be installed outdoors. Regulations require that the Power Pack shall be installed outside the pool zone. -
Page 7: Installa On Diagram
4. POWER PACK & CELL ELECTRODE INSTALLATION 4.3 Installa on Diagram POWER PACK Ensure good WARNING: DO NOT plug in if carton has been wet. ven la on Water turbulance has less impact on plates with entry this end but CELL Cell can be plumbed either way. -
Page 8: Power Pack Opera On
15%. Press the + Bu on and the chlorine produc on will increase by approximately 15%. When all green LED Output Lights are on this indicates 100% output. 5.7 Output LEDS’s There are 8 Output LED’s on your Talline display. Each one of the LED’s indicate the chlorine production output. -
Page 9: Direc On Led
Systems agent for assistance. 5.9 Water Flow LED A Water Flow sensor comes standard with your Talline unit. If flashing Red this indicates insufficient flow of water in the cell housing or a fault. Contact your local Crystal Aquatic Systems agent for assistance. -
Page 10: Timer Se Ng
6. TIMER SETTING Your Talline™ unit comes with a simple to operate quartz mechanical Timer which has a built in ba ery back up function. This area of set up is cri cal and we recommend you take me to read it and understand why we recommend certain se ngs. - Page 11 6. TIMER SETTING To adjust the me of the clock, simply hold the outside of the white segments and turn the dial un l the clock reads the right me and the number near the mer on/off arrow is close to the same number. This me is set at 8:00am and the dial pointer shows the 8:00 posi on as does the clock face hands The Timer comes on where the pins that are pressed...
-
Page 12: Water Chemistry
Cell. Salt is the essential element by which your unit operates. Not enough salt means not enough chlorine – this simple rule governs the total operation of your Talline™ unit, and insufficient salt will damage your Cell. - Page 13 7. WATER CHEMISTRY 7.3 pH Measurement Interval: Once a week Ideal pH Levels: • Concrete Pools: 7.4 – 7.6 • Fibreglass/Vinyl Pools: 7.0 – 7.2 A pH of 8.0 makes your chlorine only about 26% efficient so that is why it is cri cal to keep your pH in range.
-
Page 14: Chlorinator Maintenance
The Talline™ Chlorinator Power Pack has small air vents to allow internal components to remain cool in hot weather. The Talline™ Chlorinator has a special oil spray applied to the inside of the unit during production to stop the insects from entering the unit. To help assist in keeping the insects away, apply a surface spray periodically on the wall or post that the unit is mounted on. -
Page 15: Inspec Ng And Cleaning The Cell Electrode
Cell Housing. For cleaning, please follow these steps: • Switch off the wall outlet switch as this ensures the pump and Talline™ unit will not turn • Unscrew the Cell Locking Ring and remove the electrode for inspec on. If calcium build–up is present, immerse the electrode in cell cleaning solu on. -
Page 16: Chlorinator Troubleshoo Ng
9. CHLORINATOR TROUBLESHOOTING If you suspect for any reason your Talline™ Chlorinator is not performing or running as it should be, here are some handy troubleshooting tips that may assist you. 9.1 Not opera ng at all – no lights... - Page 17 9. CHLORINATOR TROUBLESHOOTING 9.4 Sign of mel ng or burning of the Junc on Box Poten al Cause Remedy If melted then it will need replacing otherwise The screws were not adequately ghtened during ghten as required installa on Return for service if melted 9.5 Power Pack only works in one direc on Poten al Cause Remedy...
-
Page 18: Specifica On Table
10. SPECIFICATION TABLE CHLORINATOR SIZING CHART TL45 TL35 TL25 TL15 POOL SIZE (1.000 LITRES) All measurements are based on Tropical Climates (Noosa & North) For very low bather load you can downsize by 10-20% Always try and oversize by 20-30% Warmer Climates (Sydney to Brisbane) For very low bather load you can downsize by 10-20% Cooler Climates (Melborne, Adelaide,etc.) -
Page 19: Warranty
THIS EQUIPMENT HAS BEEN MANUFACTURED AND TESTED TO THE HIGHEST STANDARD AND ACCORDINGLY CARRIES THE FOLLOWING WARRANTY. The Talline™ Power Pack will be repaired at no charge for a period of 24 Months from the date of 11.1 purchase should it be found, a er examination, that the failure has been caused by faulty workmanship or materials. -
Page 20: Technical Support
No liability or responsibility is accepted for any loss suffered as a result of any user’s reliance on such content. Repairs should only be carried out by qualified persons or Talline™ appointed agents. Crystal Aquatic Systems reserve the right to refuse warranty if any damage caused to the chlorinator or auxiliary pool equipment that is not a result of a manufacturer’s defect.