Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for VALPAR VCWS14
- Page 1 COMPONENT WORK SAMPLE 14 Integrated Peer Performance MAINTENANCE MANUAL...
- Page 2 Copyright © 2003 VALPAR International Corporation P.O. Box 5767 Tucson, Arizona 85703-5767 All rights reserved. No part of this manual may be reproduced or used in any form or by any means, electronic or mechanical, including photocopying or recording, or by any information...
-
Page 3: Table Of Contents
Functions Properly Microswitch Check and Adjustment..............2 Wheel Position Check..................3 Trouble Shooting Table ................... 4 VCWS14 Control Box Removal ..............5 and Installation Microswitch Removal and Installation............. 5 Motor Removal and Installation ..............5 Set Screw Tightening Procedures..............7 Drawings 14.1... -
Page 4: Introduction
VCWS14 Maintenance Manual covers all models of the VCWS14 built from 1974 to the present. The models of the VCWS14 can be divided into three categories: 1) models built from 1974 to 1985, 2) models built from 1985 to the present, 3) models built for international use. Please refer to the sections of this Maintenance Manual, which pertain to your VCWS14. -
Page 5: Determining If The Vcws14
These timing intervals are preset at the factory. If adjustment is needed the control box will need to be sent to the Valpar plant to be serviced by a qualified technician. The table should stop with the assembly sections in the center of the work stations. -
Page 6: Wheel Position Check
WHEEL POSITION CHECK One problem exclusive to the present model VCWS14 table (1985 or later) is that the microswitch will get stuck on the stops. This usually occurs when the table is first turned on and is not warmed up. To determine if this is the problem, look between the red wheel and the table near the control box. -
Page 7: Trouble Shooting Table
PART 2 VCWS14 TROUBLE SHOOTING TABLE 1/25/00 PROBLEM POSSIBLE CAUSE SOLUTION VCWS14 WILL 1) BLOWN FUSE REPLACE FUSE NOT BEEP 2) DEFECTIVE CONTROL BOX CALL VALPAR CUSTOMER SERVICE 3) BREAK IN WIRES REWIRE VCWS14 REFER REFER TO FIGURE 14.2 4) MICROSWITCH IS... -
Page 8: Vcws14 Control Box Removal
Be sure the roller (small microswitch wheel) is to the left when the angle faces toward the front. On the VCWS14 manufactured prior to 1985, three wires will need to be connected to the microswitch. For units manufactured after 1985, only two wires are connected. - Page 9 I) Models Built Prior to 1985 On models built prior to 1985 the motor is mounted with an angle bracket. Remove the three bolts that fasten the motor to the angle bracket. Loosen the Allen set screws located on the pedestal between the motor and the red wheel.
-
Page 10: Set Screw Tightening Procedures
III) Models Built from 1987 to Present The present model VCWS14 motor is suspended from the table and is fastened with a metal bracket. Two nylon bolts with rubber ends pass through the bracket and fasten tightly against the back of the motor housing. Loosen the nuts on both nylon bolts with a 9/16" wrench. -
Page 11: Work Sample Diagram
Figure 14.1... -
Page 12: Wiring Diagram Models From 1974 To 1985
Wiring Diagram MODELS FROM 1974 TO 1985 Figure 14.2... -
Page 13: Wiring Diagram Models From 1985 To Present
Wiring Diagram MODELS FROM 1985 TO PRESENT Figure 14.3... -
Page 14: Wiring Diagram International Models 1985 To Present
Wiring Diagram INTERNATIONAL WIRING FROM 1985 TO PRESENT Figure 14.4... -
Page 15: Microswitch Diagram
Figure 14.5...