Page 1: Table Of Contents
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. CONTENTS Safety Precautions and Warnings General Information Exterior of the Device Maintenance and Operation Installation of SIM-Cards Software Installation Setup Wi-Fi for AP and AP+STA Mode Operation Replacement of the Accumulator Battery...
Page 2: Safety Precautions And Warnings
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. SAFETY PRECAUTIONS AND WARNINGS NOT ALLOWED TO CONNECT THE DEVICE TO REPEATERS! THE SIGNAL LEVEL OF OVER 1 mW (+0dBm) CAN CAUSE DAMAGE DEVICE. BE CAREFUL WHEN CONNECTING OF THE DEVICE TO EXTERNAL LINE AMPLIFIERS.
Page 3: General Information
USER MANUAL ©2012-2014 SDE Lab. GENERAL INFORMATION Cellular Meter 2G/3G is a portable measurement instrument which designed to assistance at deployment and maintenance of cellular repeaters and other cellular equipment. Cell Meter allows monitoring of the radiofrequencies within the main cellular bands: EGSM 900, GSM 850, DCS 1800, PCS 1900, 3G 2100 (3GPP Band I) and 3G 900 (3GPP Band VIII).
Page 4: Exterior Of The Device
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. EXTERIOR OF THE DEVICE Picture 1. Exterior of the device in the closed and open state. 1 Removable front bezel. 7 RF INPUT connector (+0 dBm max). 2 Front bezel screws. 8 RF OUTPUT connector (+10 dBm max).
Page 5: Maintenance And Operation
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. MAINTENANCE AND OPERATION For proper operation of Cell Meter, make sure that RF connectors are in good condition. Wipe them with a clear alcohol when clean necessary. Strongly recommended to close connectors with safety caps for not only the transportation, but also when not in use.
Page 6: Software Installation
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. Carefully place accumulator battery and its wires inside the case. Assemble device in the reverse order. Avoid to damage wires insulation when close the lid. Not recommended to apply force when tightening the screws of the front bezel - it is just a plastic.
Page 7: Replacement Of The Accumulator Battery
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. network will not arise and the WEB interface will be only accessible by the IP address set by the local network router. For further software operation with the device find out its IP address and enter it in the “CELLMETER” software settings.
Page 8: Short Software Description
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. Caution! If you connect an accumulator with improper polarity, this will damage both the device and the accumulator battery. In this case, battery can be explosion-dangerous! Connect the new accumulator to the device. Switch on the device to check operability.
Page 9: Main Features Of Windows Based Software
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. gives a lot of additional information on the system. In this mode, the device is trying to register in the network of the selected operator. This function is similar to service monitor mode of cellular phones, but data displayed in a more convenient form and table.
Page 10: Main Features Of Android And Apple Ios Software
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. Caution! Simultaneous operation of two or more devices in the Wi-Fi access point mode not provided. For the USB operation, first make sure that device is off, then check cable connection and then switch on the device. The red LED blinking will indicate cable data mode.
Page 11: Warranty And Post-Warranty Service
Cellular Meter 2G/3G USER MANUAL ©2012-2014 SDE Lab. WARRANTY AND POST-WARRANTY SERVICE The manufacturer shall perform warranty repair (elimination of manufacturing defects) of the device within 12 months upon the date of its retail sale. The accumulator battery warranty is 6 months upon the date of sale, but no more than 12 months upon the date of manufacture.