Related Manuals for Advantek PixLite R2F-S
Summary of Contents for Advantek PixLite R2F-S
- Page 1 PixLite R2F-S User Manual Hardware Rev 1.0 - 1 - www.advateklights.com PixLite R2F-S User Manual V200702...
-
Page 2: Table Of Contents
5.1 - Operating Specifications 5.2 - Mechanical Specifications 5.3 - Fault Protection 6 - Troubleshooting 6.1 - No Power LED 6.2 - No Pixel Control 6.3 - Other Issues 7 - Disclaimer - 2 - www.advateklights.com PixLite R2F-S User Manual V200702... -
Page 3: Introduction
(1000') or more over a standard network cable from a PixLite T8 transmitter unit, and convert these input signals back into a pixel-ready signal for output directly to pixels. The PixLite R2F-S features 2 pixel outputs , each having both a dedicated fuse and 'fuse good' LED indicator. -
Page 4: Installation
3 - Installation 3.1 - Supplying Power Power is applied to the PixLite R2F-S via the large lever clamp connector. The levers should be lifted up for wire insertion and then clamped back down, providing a highly robust and secure connection. Polarity for the connector is clearly marked on the lid,... -
Page 5: Data Input
Figure 2 below. Figure 2: Internal View of the PixLite R2F-S 3.3 - Data Input Data is connected via a standard network cable into the RJ45 jack located on the front panel of the unit, as shown in Figure 3 below. - Page 6 For this reason, the standard network cable you use can be safely used in excess of 300m. Figure 4: Correct equipment to use A typical setup is shown in Figure 5 below, which also shows how many pixels can be run off each output. - 6 - www.advateklights.com PixLite R2F-S User Manual V200702...
-
Page 7: Connecting Pixel Leds
The cable length between the output and the first pixel should not exceed 15m. Figure 6 shows the pin-out of the pixel output connectors. - 7 - www.advateklights.com PixLite R2F-S User Manual V200702... - Page 8 Figure 6: Pixel Output Pinout - 8 - www.advateklights.com PixLite R2F-S User Manual V200702...
-
Page 9: Operation
If the switch is pushed to the right, it is off, and all indicator LEDs and the power LED will always be off. This switch is shown in Figure 8 below. - 9 - www.advateklights.com PixLite R2F-S User Manual V200702... -
Page 10: Outputs
Refer to the user manual of the PixLite Transmitter device for more information about this topic as the Transmitter will be responsible for the refresh rate of this receiver. - 10 - www.advateklights.com PixLite R2F-S User Manual V200702... -
Page 11: Specifications
5 - Specifications 5.1 - Operating Specifications The table below specifies the recommended operating conditions for a PixLite R2F-S receiver. Parameter Value/Range Units Input Voltage Range 5-24 V DC Max Current Max Logic Current Consumption Ambient Operating Temperature -20 to +55 °C... -
Page 12: Fault Protection
Figure 9: Receiver Mechanical Specifications 5.3 - Fault Protection The PixLite R2F-S features notable protection from potential damage due to various types of faults. This makes the device extremely robust and reliably able to withstand installation and operation even in harsh environments. - Page 13 The PixLite R2F-S itself is protected against damage from reversed polarity power input. However it does not provide external reverse polarity protection for any loads that you may have connected to the pixel outputs. - 13 - www.advateklights.com PixLite R2F-S User Manual V200702...
-
Page 14: Troubleshooting
If you can’t resolve your problem with the help of our knowledgebase, you can send an e-mail to: support@advateklights.com and a support ticket will automatically be created for you, or you can manually open a support ticket here: www.advateklights.com/support - 14 - www.advateklights.com PixLite R2F-S User Manual V200702... -
Page 15: Disclaimer
This product has been manufactured by: Advatek Lighting 16 / 52 Corporate Blvd Bayswater, 3153 VIC, AUSTRALIA - 15 - www.advateklights.com PixLite R2F-S User Manual V200702...
Need help?
Do you have a question about the PixLite R2F-S and is the answer not in the manual?
Questions and answers