Introduction The Quilt Maker Pro 5’ Quilting Frame can be set up to work with the Janome Quilt Maker Pro 16 or 18 machine. The frame enables you to use the machine within a small footprint, yet you can do quilts of any size.
1 – Left side arm 14 – M6 x 10mm socket button head cap screws, (#QF10007-JA, Box 1) (#QF10008-JA, Box 1) cap screws; 1 more SBHCS, with Flange comes in each of the (#QF10959, Box 1) knob assemblies. (#QF10006, Box 1) Janome...
Page 3
Right Side arm Right Side arm Left Side arm Corner Connector Side Arm Pole L-Bracket Corner Connector 2 – Front pole corner 4 – L-brackets Side Arm Pole Corner Connector Side Arm Pole 2 – Side arm pole connectors (#QF10010, Box 1) (#QF10004, Box 1) (#QF10003, Box 1) -Bracket...
Page 4
Clamps (QF10018, Box 1) Clamps (QM10014, Box 1) (HG10000, Box 1) 2 - 5’ track insert 2 - Track Support 5’ 6 - Screws, track support (QF00001-05) (QF05300-02 to table top M6 x 12 with large washer head (QF09318-303) Janome...
Page 5
Table and Leg Assembly Parts Needed Tools Required 1 - Table top section 5 mm hex tool (provided) 2 - Upper leg A 17/13 mm wrench (provided) 2 - Upper leg B Spirit level (not provided) 2 - Lower legs 4 - Leveling feet 20 - M8 x 20 mm socket button head cap screws...
Page 6
Front of Frame Back of Frame 7. Use the 17/13 mm wrench to tighten the leveling foot, leaving about 1/2 inch of threads exposed to make it easier to level the frame later. Janome...
Page 7
8. Set the frame height: Decide on the preferred height of the frame. Use the image at the right to identify which height adjustment holes to use for securing the 33” - 34” FLOOR TO QUILT PLANE lower legs. 34” - 36” FLOOR TO QUILT PLANE 36”...
Use the second set of holes down from point the top of the side arm bracket for both the 16” and 18” machines. Janome...
Page 9
2. Use the 4 mm hex tool to screw one of the M6 x 10mm socket cap screws to secure the side arm to the L-bracket on table-top frame. 3. Tighten the two large screws with a 5mm hex tool and the small screw with a 4mm hex tool.
Page 10
(see arrow). Repeat with the other side of the frame. push button in the second hole for the 16” machine setting. Set up for a 16-inch machine 10 | Janome...
Page 11
7. Assemble the front pole: Identify the front pole corner connectors. Press in the button on one of the front pole corner connectors and insert it into the left side of the front pole until the button snaps in place. Press in the button on the other front pole corner connector and insert it into the right side of the front pole until the button...
Page 12
If you are setting up the frame for an 18-inch machine, align the holes in the L-bracket with the side arm holes as shown in the figure at the right (front two holes on the side arm). Set up for an 18-inch machine. 12 | Janome...
Page 13
Set up for 16-inch machine: If you are setting up the frame for a 16-inch machine, align the holes in the L-bracket with the side arm holes as shown in the figure at the right (back two holes on the side arm). Set up for a 16-inch machine 10.
M6 x 10 mm socket cap screws. 7. Starting at one end of the frame, and with the carriage and machine over each front screw, tighten the front retaining screw fully with the 4mm hex tool. 14 | Janome...
Leveling the Frame Using a spirit level, check and adjust the frame top to be level in the place where it will be used, both front to back and side to side, by adjusting the leveling feet. If no spirit level is available, check the table with the machine on the carriage and the tracks.