Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for eZLO Vera VistaCam 1200
Summary of Contents for eZLO Vera VistaCam 1200
- Page 1 VistaCam 1200 Wi-Fi Doorbell Camera Quick Start Guide...
- Page 2 Congratulations on choosing the VistaCam 1200 You’ve taken the next step toward making your home safer and your life easier. It’s easy to set up your camera. Here’s what you need to do.
-
Page 3: Regulatory Information
Regulatory Information FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. - Page 4 If you haven’t already set up your Vera or Ezlo controller, please do that first. There are instructions on how to do so accompanying the controller.
- Page 5 Now let’s set up your doorbell. Once the wiring is done we’ll add it to your system.
- Page 6 What's in the Box Doorbell (x1) Faceplate (x3) Pick the one that best matches your home from three faceplates. Mounting Plate (x3) Plate Foam (x1) Pick the one for best surveillance Stabilize the mounting angle. plate when installing it on a rough surface.
- Page 7 What's in the Box Wire Connectors (x4) Mounting Screws (x3) Power Kit (x1) Anchors (x3) Security Screws (x2) Fixing Screws (x2) U-shaped Wires (x2) Doorbell Screws (x2) Wire Harness (x1) Fuse Wire (x1) Screwdriver (x1) Mini-Level (x1) Drill Bit (x1) Pencil Tools You May Need Drill...
- Page 8 Before doing anything else, shut off the breaker that controls the doorbell's circuit. If you have a mechanical chime installed in your home, install the power kit and doorbell. If you have an electronic chime installed in your home, refer to its own manual to install the power kit, and install the doorbell.
- Page 9 Install the power kit Insert one end of the wire harness into the power kit. Remove the cover from your mechanical chime. Remove the existing chime wires in the terminals named TRANS and FRONT.
- Page 10 Install the power kit Connect the wire harness to the chime's terminals named TRANS and FRONT. Insert the existing chime wire and the other end of the wire Wire Connector harness into the wire connector and twist it tightly. Repeat this step with the other chime wire.
- Page 11 Install the power kit Mount the power kit to the side of the chime. Put back the chime cover.
- Page 12 Install the doorbell Ensure the electricity at the breaker that controls the doorbell's circuit is still off. (Optional) When the wall is uneven, paste the plate foam to the mounting plate. Insert the mini-level into the mounting plate and mark the drill points when its bubble stays in the Mini-Level middle.
- Page 13 Install the doorbell Drill holes according to drill points and insert anchors. Anchor Fix the mounting plate to the wall. Mounting Screw Remove the faceplate on your doorbell from bottom to top.
- Page 14 Install the doorbell Connect the doorbell with your existing doorbell wires. Fixing Screw U-Shaped Wire...
- Page 15 Install the doorbell Fix the doorbell to the mounting plate by inserting the doorbell screws. Doorbell Screw Restore the electricity at the breaker. Doorbell is powered on when its indicator flashes blue quickly. If you see this blue flash, proceed to the doorbell setup.
- Page 16 Doorbell Setup In the Vera app, navigate to the Devices screen and tap + in the top right corner. Select doorbells and look for the VistaCam 1200. Follow the prompts to finalize the setup. If you want to change your Reset doorbell’s Wi-Fi, press and Button...
- Page 17 Basics Mounting micro SDCard Slot Terminals Holes Reset Button Hold for 5s to reset and enter to AP mode. LEDIndicator Blue Light Flashing Doorbell is ready for Wi-Fi configuration. Steady on Doorbell is working. Red Light Flashing Fast Device Exception. Steady on Doorbell is powering on.
- Page 18 Your doorbell is now set up! You can now talk to people at your door through the Vera app and ensure greater security for your home.
- Page 19 Need help setting up? You can reach our Customer Care team seven days a week at 866.966.2272 between 6am and 10pm US CST/EST* or at support@getvera.com You can also purchase our Vera Easy Start service and get one hour of personalized setup assistance through a phone call with one of our most experienced agents.
- Page 20 You’re now ready to enjoy smarter home control. © Ezlo Innovation 2020...
Need help?
Do you have a question about the Vera VistaCam 1200 and is the answer not in the manual?
Questions and answers