Huka TXDW Quick Start Manual

UNIVERSAL REMOTE

Best position for duplication

Original
Duplicator
(Original remote control on the top of Duplicator)

Auto-scan Type

Multi-frequency 280~870Mhz

Up to 4 different remotes in 1

Duplicating procedures:

-Standard (duplicating)

1. Press and hold button A of the Duplicator,
meanwhile press 4 times the button B, then
release both buttons, the LED emits a short
flash every 2 sec.
2. Place the Original remote control on the
top of Duplicator.
3. Keep pressing the button of the original re-
mote control until the LED starts flash quickly.
4. While the LED is flashing, press the button
of the Duplicator where you want to store the
remote's code just copied, until the led will
turn off.(Step 1 to 4 video link:
https://youtu.be/mOxFoAC9Etc)
5. Select and activate the correct procedure
in the , RCS , RCC procedures to
S C
complete the final step(see the compatibility
list present in this manual).
means simple code, the duplicator
S C
can be used directly after duplicating
means rolling code simple, You need
RCS
to insert the new remote into the rec-
eiver according to the steps given by
the automation manufacturer.
(Video link reference:
https://youtu.be/OdSzvA1jl00)
means rolling code complex,
RCC
1. First of all you must be closed to
the automation.
2. Keep pressing the programmed
button during 10seconds, when the LED start to flash,
release the button.
3. Wait until the LED will turn off. The operation has been
done, now you can use your new remote control.
(Video link reference:
https://youtu.be/c1Y2VCKM_mw)

-BFT (duplicating)

1. Press and hold button A of the Duplicator, meanwhile
press 4 times the button B, then release both buttons, the
LED emits a short flash every 2 sec.
2. Place Original remote control on the top of Duplicator.
3. Keep pressing the button of the original remote control
until the LED turn on with a fix light and then emits a doub-
le flash every 2 sec.
4. Place Original remote control on the top of Duplicator.
5. Emit now the SEED CODE of the BFT original remote
control, press the 1 and 2 buttons simultaneously until the
original remote control LED switches on.
6. Now the Duplicator LED will flash quickly, press the
button where you want to store the code just copied, until
the LED will turn off.
7. Activate now the
RCC
remote control on the receiver.

-FAAC / GENIUS (duplicating)

Attention: verify the programming remote control is a
MASTER. Pressing whatever button, the LED has to emit
a double flash rather than to switch on as a fixed light.
1. Press and hold button A of the Duplicator, meanwhile
press 4 times the button B, then release both buttons, the
LED emits a short flash every 2 sec.
2. Place Original remote control on the top of Duplicator.
3. Keep pressing the button of the original remote control
until the LED turn on with a fix light and then emits a doub-
le flash every 2 sec.
4. Emit now the SEED CODE of the FAAC/GENIUS origi-
nal remote control, press the 1 and 2 buttons simultaneo-
usly until the original remote control LED flashing.
5. While the FAAC/GENIUS LED is flashing, place it on
the top of the Duplicator and press the button that you
want to copy.
6. Now the Duplicator LED will flash quickly, press the
button where you want to store the code just copied, until
the LED will turn off.
7. Activate now the S C
the new remote control on the receiver.

-V2 (duplicating)

1. Press and hold button A of the Duplicator, meanwhile
1
procedure to insert the new
or RCC procedure to insert
2
press 4 times the button C, then release both buttons,
the LED emits a short flash every 2 sec.
2. Place Original remote control on the top of Duplicator.
3. Keep pressing the button of the original remote control
until the LED turn on with a fix light and then emits a doub-
le flash every 2 sec.
4. Keep pressing once again the same button of the origi-
nal remote control until the LED starts flash quickly.
5. While the LED is flashing, press the button of the Dupl-
icator where you want to store the remote's code just
copied, until the led will turn off.
6. Activate now the procedure to insert the new
RCC
remote control on the receiver.

COMPATIBILITY LIST

BRAND MODEL
ACM TX2, TX2 COLOR, TX4
ADYX TE4433H BLUE, 433-HG BRAVO
COMPACT, HY-DOM, MERCURI B/C,
SABUTON, MARS, SATURN, ST3/N,
AERF
TERRA, TMP-1/2, UNITECH
BROWN, BROWN RED, BRO.OVER,
ALLMATIC
PASS, MINIPASS, TECH3
APERIO GO, GO PRO, GO MINI
TX02-868-2 BLUE, 4025 TX02-868-2,
TX02-434-2, 4022 TX02-434-2,
APERTO
(Sommer)
TX-03-868-4, 4020 TX03-434, 4013,
TX03-434-4
APRIMATIC TR2, TR4, TM4, TXM
ATA PTX4 BLUE, PTX4 PINK
104250, 104250 RED, 104250 OLD,
AVIDSEN
104251, 104257, 104350, 654250
BALLAN FM400, FM400E, FM404B, 4013
LOT 1W/2W/4W/1WM/2WM/
WCV/2WCV, T2W,T4W
TO GO. WV, TWV, ROLLKEY, APPLE,
BENINCA
CUPIDO, TO.GO. QV
IO
BESIDE BEZAP, HIT
MITTO, MITTO M/A/B/RCB, GHIBLI,
MURALE, KLEIO
BFT
TRC, TE 01/02/04, RB4 MURALE
T431/434, TAM432SA, TOP 432/432A
CAME
/434A/432NA/432EE/432EV
MARK
RCS
RCC
RCC
RCC
S C
RCS
RCC
RCS
RCS
RCS
S C
RCC
RCS
S C
RCC
S C
S C
3