Advertisement
Quick Links
INSTALLATION INSTRUCTION
InvisiLED® Classic Outdoor 24V
LED-TO24
SAFETY INSTRUCTION
•
Read all instructions before installing.
•
Always turn off power at fuse box prior to installation to prevent electrical shock.
•
Intended for out door use, damp and wet locations are permitted.
•
For installation by a qualified electrician.
•
System is intended for installation in accordance with National Electric Code, and local regulations.
INVISILED™ CLASSIC OUTDOOR
•
Determine the installation area and material, based on different mounting materials (wood or concrete), different mounting
accessories will be needed.
WIRING AND INSTALLATION:
Please refer to installation diagrams shown on next page.
1.
Determine the number of separately powered runs needed. Calculate the number of power supplies.
2.
Measure the length of each run and round it off to the nearest 1 foot interval. Determine the necessary quantities
of 1ft, 5ft, and 10ft sections.
3.
Count the number turns in the runs in order to determine the number of X, and Y connectors.
4.
If making lateral turns at angles other than 90°, determine the number of joiner cables necessary to make
the lateral adjustment.
5.
Connect to incoming 120V supply.
Hard Wire
•
Power supply is IP67 rated for damp and wet locations. The power supply should be installed
accessible for service
•
Connect building wires to like color power supply wires with wire nuts in the outdoor junction box.
Building ground wire my be green or un-insulated, and attaches to green wire from power supply box.
6.
Connect the output female connector of the power supply with the male connector of the outdoor InvisiLED tape
or lead wires, to form straight lines or turns around the installation surface.
7.
End caps of each InvisiLED can be connected together to form a straight run.
8.
Classic outdoor LED sections may be cut at every 2 inch intervals.
9.
Terminate each separately powered run with an end cap. Install the end cap with silicon for water tight.
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FebruAry, 2015
Tape Lights have polarity for connection.
Min. / max. run length
Current
Power consumption
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
1ft / 40ft per run
100 mA/ft
2.0 Watts/ft
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Advertisement
Related Manuals for WAC Lighting InvisiLED Classic Outdoor 24V
Summary of Contents for WAC Lighting InvisiLED Classic Outdoor 24V
- Page 1 Phone (800) 526.2588 • Fax (800) 526.2585 Phone (516) 515.5000 • Fax (516) 515.5050 Phone (800) 526.2588 • Fax (800) 526.2585 WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FebruAry, 2015...
- Page 2 Phone (800) 526.2588 • Fax (800) 526.2585 Phone (516) 515.5000 • Fax (516) 515.5050 Phone (800) 526.2588 • Fax (800) 526.2585 WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FebruAry, 2015...
- Page 3 Phone (800) 526.2588 • Fax (800) 526.2585 Phone (516) 515.5000 • Fax (516) 515.5050 Phone (800) 526.2588 • Fax (800) 526.2585 WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FebruAry, 2015...