Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for AND-Tech AVR Prog MKII
- Page 1 AVR Prog MKII MANUAL AVR Prog MKII manual www.and-tech.eu...
-
Page 2: Table Of Contents
5. Environment protection ATTENTION!! AVRISP mkII programmer is compatible with BASCOM and AVR DUDE environment. If you want to use this programmer with AVR Studio, you need to update its firmware (instruction in chapter 3: Firmware update) AVR Prog MKII manual www.and-tech.eu... -
Page 3: A) Driver Installation
When programmer is installed successfully, green LED diode should turn on. If not, connect programmer directly to PC or laptop without HUBs or dock stations. In some cases, programmer doesn't work properly with these devices. AVR Prog MKII manual www.and-tech.eu... - Page 4 After you accept licence agreement and chose installation path, you should see window presented in Picture 2. Check only first position – Runtime Files and click Next. Picture 2 Check Instalall libusb-win32 with filter capabilitied? as in Picture 3 and click Next. AVR Prog MKII manual www.and-tech.eu Picture 3...
- Page 5 Picture 4 Start Filter Wizard. It is available in the following path: Start >Programy >LibUsbDotNet >libUsb- win32 >Filter Wizard. Picture 5 AVR Prog MKII manual www.and-tech.eu...
- Page 6 In window Install/Remove Device Filter(s) choose first option: Install a device filter- Picture 6. Picture 6 Now, please find device AVRISP mkII, as in Picture 7. Picture 7 If installation is successful, the following window appears: Picture 8 Programmer is installed correctly. AVR Prog MKII manual www.and-tech.eu...
-
Page 7: B) Configuration
Configuration 1. BASCOM ATTENTION!! AVR Prog MKII is supported by BASCOM 2.0 and higher. If you work with older version please use additional program AVRDUDE. We need to configure programmer to make it work with BASCOM environment. Please, start BASCOM and find programmer settings (Options >Programmer). - Page 8 Picture 10 Click Program chip icon in order to program circuit. Picture 11 AVR Prog MKII manual www.and-tech.eu...
- Page 9 Flash, EEPROM, Lock and Fuse bookmarks show state of FLASH, EEPROM memory and fuse bits after sending current program to processor. Button: - identifies processor - checks if processor's memory is empty - erases processor's memory and sends new program AVR Prog MKII manual www.and-tech.eu...
-
Page 10: Avrdude
After you extract it, turn on graphical user interface: avrdude-GUI.exe and then choose from list Programmer: Atmel AVR ISP mkII (avrispmkII), from list Port: - usb and from Device – choose model of processor, you want to program. Picture 13 AVR Prog MKII manual www.and-tech.eu... -
Page 11: Programming In Avr Studio
When programmer is installed successfully, green LED diode should turn on. If not, connect programmer directly to PC or laptop wihout HUBs or dock stations. In some cases, programmer doesn't work properly with these devices. b) Configuration AVR Prog MKII manual www.and-tech.eu... - Page 12 To configure AVR Prog MKII, please start AVR Studio. Programmer's options are available in Tools->AVR Programming. (Picture 14). Picture 15 From Tool list choose AVRISP mkII. List Device specifies model of processor , which you want to program and button Apply saves settings.
- Page 13 Read buttons read ID and voltage of programmed processor. Picture 17 To program processor, find Memory bookmark – Picture 17. Picture 18 AVR Prog MKII manual www.and-tech.eu...
-
Page 14: Firmware Update
To put the AVRPROG MKII into DFU bootloader mode, push bootloader button. The green led should go out indicating it is in bootloader mode. New hardware should be found. Picture 19 Please choose: Install from a list or specific location (Advanced) and find the following AVR Prog MKII manual www.and-tech.eu... - Page 15 C:/Program Files / Atmel / Flip 3.4.3 / usb. - Picture 20 Picture 20 Click OK and start FLIP program. AVR Prog MKII manual www.and-tech.eu...
- Page 16 Click on the 'chip' icon or 'Device-->Select' menu option and select the device from the menu (at90usb162) – Picture 22. Picture 22 Click on the 'USB cable' icon and select 'USB' from the menu and connect to the device. AVR Prog MKII manual www.and-tech.eu...
- Page 17 Click Open. Picture 24 Load the new hex file from the 'LOAD hex file' icon or from the 'File-->LOAD HEX file' menu. Click on the 'RUN' button in the lower left corner. AVR Prog MKII manual www.and-tech.eu...
- Page 18 DONE! Your programmer should be up to date now. Click Start Application to restart programmer. ATTENTION!! If you want your programmer to work again with BASCOM and AVR DUDE, follow this instruction again, but use the following firmware: 101116_AVRISP_avrdude.hex link: http://www.and-tech.pl/MKII/101116_AVRISP_avrdude.zip AVR Prog MKII manual www.and-tech.eu...
-
Page 19: Programmer Interface
Programmer is equipped with 10-pin ISP connector (standard KANDA). Picture 23 presents pins order. b) TPI and PDI connector Second 10-pin ISP connector consists of TPI connector (for Attiny programming) and PDI (for Atxmega programming). c) Jumpers and LED diodes Picture 28 AVR Prog MKII manual www.and-tech.eu... -
Page 20: D) Bootloader Button
3.3v – supply programmed circuit with 3,3V LED diodes: READY – programmer turn on and ready BUSSY – programmer busy (working) d) Bootloader button This button puts AVR Prog MKII into DFU bootloader mode – the green led goes Picture 29 AVR Prog MKII manual www.and-tech.eu... -
Page 21: Environment Protection
The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal waste. AVR Prog MKII manual www.and-tech.eu... - Page 22 NOTE AVRPROG MKII is powered by LUFA library, which is currently released under the MIT licence (http://www.fourwalledcubicle.com/LUFA.php). AVR Prog MKII manual www.and-tech.eu...
Need help?
Do you have a question about the AVR Prog MKII and is the answer not in the manual?
Questions and answers