Technical Data - ubbink Heatermax Compact 10 Note Of Assembly

1
Operating instructions for Heatermax Compact 10 / 20 Swimming Pool Heat Pumps
Dear Customer,
We congratulate you on your purchase of the Heatermax Compact swimming pool heat pump. The Heatermax Compact heat pump warms up the water in your pool and keeps it at a constant temperature when
the outside temperature is between 12°C and 42°C. These operating instructions include all necessary information on installation, operation and maintenance of the swimming pool heat pump. Please read through
these operating instructions in detail and keep them carefully.
ATTENTION: The installer is responsible for the installation of the product and should follow all instructions related to the installation and maintenance of the device, as well as consider all
the applicable specifications.
Dimensions
Model A
Heatermax COMPACT 10 103mm 103mm
Heatermax COMPACT 20 132.5mm 168mm

Technical data

Model
Article No.
Voltage / Frequency / Phase
Rated current
Recommended fuse protection
Mains cable
Protection class
Protection type
Heating power
Power consumption
Rate of performance (COP)
Heating power
Power consumption
Rate of performance (COP)
Max. pool volume
Min. Water flow-through
Max. water pressure
Water temperature (operating range)
Air temperature (operating range)
Inlet / Outlet
Compressor (type/brand)
Ventilation direction
Noise level at 1 m distance
Noise level at 10 m distance
Housing
Heat exchanger
Cooling gas R32
GWP value
CO2 equivalent
Length
Width
Height
Net weight
Heatermax Compact 10 / 20 include fluorinated greenhouse gases. Right to changes reserved
Safety regulations
This device was built in accordance with the current state of the art of the technology and considering the existing safety regulations. In spite of this, dangers to persons and property can arise from this device
when it is used inappropriately or not in accordance with the intended purpose or the notes on safety are not considered.
ATTENTION! According to the harmonised European directives and safety standards, any installation, service and repair work on the device, as well as installation and/or maintenance of
the mains cable, must be implemented by an authorised and qualified specialist company. Before beginning with the installation, operation, service or maintenance work, the specialist
instructed with these tasks must have read and understood the operating instructions.
• The power supply must correspond to the product specifications. Do not connect the device if the power supply does not fulfil the specified specifications (VDE 0100-702)! You can be provided with further
information by your local, accredited electrical installer.
• The electrical circuit for the device must be fused over a residual-current device (FI or RCD) with a rated leakage current of max. 30 mA.
• The heat pump must be installed at a distance of minimum 2 m from the swimming pool.
• The electrical connection of the heat pump must be located minimum 3.5 m from the swimming pool.
B C D E
51mm 375mm 310mm
50.7mm 460mm 434mm
Heating capacity in case of Condition 1: Air 27°C / water 27°C/ humidity 80%
Heating capacity in case of Condition 2: Air 15°C / water 26°C / humidity 70%
F G
300mm 356.5mm
371mm 432.5mm
Heatermax Compact 10
7505503
220-240V ~ 50Hz / 1 Phase
2,6 A
10 A
2.5 m / Plug with leakage current (Fi) protective circuit breaker
I
IP X4
2,50 kW
0,59 kW
4,2
1,90 kW
0,56 kW
3,9
10 m3
2 m3/h
15 kPa
Rotation/Mitsubishi
57 dB(A)
48 dB(A)
Rust-free zinc-coated steel
Titanium (PVC container)
150 g
675
0,19 t
310 mm
356,5 mm
365 mm
18 kg
14
Heatermax Compact 20
7505504
4,4 A
10 A
I
IP X4
4,20 kW
0,91 kW
4,2
3,20 kW
0,91 kW
3,5
m3
2 m3/h
15 kPa
15°C - 35°C
12°C - 42°C
38/32 mm
Rotation/Hitachi
Horizontal
55 dB(A)
46 dB(A)
280 g
675
0,10 t
434 mm
432,5 mm
460 mm
26 kg