Econess Energy EN125M-72 Series User Manual
  1. Manuals
  2. Brands
  3. Econess Energy Manuals
  4. Solar panel
  5. EN125M-72 Series
  6. User manual

Econess Energy EN125M-72 Series User Manual

Photovoltaic module
Hide thumbs
Table of Contents

Advertisement

Quick Links

USER MANUAL
PHOTOVOLTAIC MODULE
-1-

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EN125M-72 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Econess Energy EN125M-72 Series

  • Page 1 USER MANUAL PHOTOVOLTAIC MODULE...

  • Page 2: Table Of Contents

    Photovoltaic Module User Manual Effective April 1, 2020, Version 3.3 Table of Contents: 1. General information………………………………..……..…..…………….3-5 1.1 Overview 1.2 Applicable Products 1.3 Warning 2. Installation……………................6-11 2.1Installation safety 2.2Installation condition 2.2.1 Operation condition 2.2.2 Site selection 2.2.3 Tilt angle selection 2.3 Mechanical Installation introduction 2.3.1 Fixation with screw 2.3.2 Fixation with clamps 3.

  • Page 3: General Information

    1. General Information 1.1 Overview Thanks for choosing Econess Energy PV modules. In order to ensure the PV modules to be installed correctly, please read the following operation instructions carefully before installing and using the modules. Please remember that the products would generate electricity and certain safety measures need to be taken to avoid danger.
  • Page 4 PV modules generate DC electrical energy when exposed to sunlight or other light sources. Active parts of module such as terminals can result in burns, sparks, and lethal shock ⚫ Artificially concentrated sunlight shall not be directed on the module or panel. ⚫...
  • Page 5 ⚫ Do not remove any part installed by Econess Solar or disassemble the module. ⚫ All instructions should be read and understood before attempting to install, wire, operate and maintain the module. ⚫ Please don’t lift up PV modules using the attached cables or the junction box. ⚫...

  • Page 6: Installation

    2. Installation 2.1 Installation safety ⚫ ways wear protective head gear, insulating gloves and safety shoes (with rubber soles). ⚫ Keep the PV module packed in the carton until installation. ⚫ Do not touch the PV module unnecessarily during installation. The glass surface and the frame may be hot.

  • Page 7: Site Selection

    ﹡Note: The mechanical load bearing (include wind and snow loads) of the module is based on the mounting methods. The professional system installer must be responsible for mechanical load calculation according to the system design. 2.2.2 Site selection In most applications, Econess solar PV modules should be installed in a location where they will receive maximum sunlight throughout the year.

  • Page 8: Mechanical Installation Introduction

    For standalone systems with batteries where the PV modules are attached to a permanent structure, the tilt angle of the PV modules should be selected to optimize the performance based on seasonal load and sunlight. In general, if the PV output is adequate when irradiance is low (e.g., winter), then the angle chosen should be adequate during the rest of the year.
  • Page 9 8 9*14mm mounting holes lght The inner mounting holes lght The outside mounting holes Figure 2 above: PV module installed with Screw fitting method* 2.3.2 Independent installation of Z-type clamp single module The module clamps should not come into contact with the front glass and must not deform the frame.
  • Page 10 The detailed installation method shall be seen in the following sketch: Figure3 above: PV module installed at long side with Clamp fitting method D i m e n s i o n s ( m m ) C e l l M o u d l e t y p e C e l l t y p e q u a n t i t y...
  • Page 11 Figure 4 above: PV module installed at short side with Clamp fitting method D i m e n s i o n s ( m m ) C e l l M o u d l e t y p e C e l l t y p e q u a n t i t y A * B...

  • Page 12: Wiring And Connection

    3. Wiring and connection a) Before this procedure, please read the operation instructions of the PV system carefully. Make wiring by Multi-connecting cables between the PV modules in series or parallel connection, which is determined by user’s configuration requirement for system power, current and voltage.
  • Page 13 Econess modules can also be grounded using third party ground washers or clip devices as long as the products are approved for grounding metallic frames of PV modules. Alternate grounding options built into the racking system are acceptable so long as they have been UL approved -13-...
  • Page 14 It is recommended that the screw be tightened to a torque of 2.3 and 2.8NM j) The cable of the junction box is defined as L1, as showed below. For Econess Energy standard module, L1 is 900 mm; and for customized module, L1 can be 1000mm. Please base on your condition, take the cable length into consideration before designing the wiring layout.

  • Page 15: Maintenance And Care

    4. Maintenance and care a) A built up of dust or dirt on the module(s) front face will result in a decreased energy output. Clean the panel(s) preferably once per annum if possible (depend on site conditions) using a soft cloth dry or damp, as necessary. b) Never use abrasive material under any circumstances.
  • Page 16 5.1.Electrical specifications of EN156P-72- xxx (xxx=300-350) Series Poly-crystalline solar modules EN156P-72 EN156P-7 EN156P-72 EN156P-72 EN156P-72 EN156P-7 EN156P-72 EN156P- EN156P-72 EN156P-72 EN156P-72 Module Type -300 2-305 -310 -315 -320 2-325 -330 72-335 -340 -345 -350 Maximum Power (Pmax) Maximum Power Voltage 35.85 36.19 36.48...
  • Page 17 5.2.Electrical specifications of EN156P-60- xxx ( xxx=250-290)Series Poly-crystalline solar modules EN156P-60 EN156P-60 EN156P-60 EN156P-60 EN156P-60 EN156P-6 EN156P-60- Module Type EN156P-60-285 EN156P-60-290 -250 -255 -260 -265 -270 0-275 Maximum Power (Pmax) Maximum Power Voltage 30.16 30.45 30.72 31.04 31.35 31.71 32.05 32.33 32.64 (Vmp)
  • Page 18 5.3.Electrical specifications of EN156P-54- xxx（xxx = 225 - 260) Series Poly-crystalline solar modules EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 EN-156M-54-2 Module Type Maximum Power at 225Wp 230Wp 235Wp 240Wp 245Wp 250Wp 255Wp 260Wp STC(Pmax) Maximum Power Voltage 27.4V 27.49V 27.63V 27.78V 28.22V...
  • Page 19 5.4.Electrical specifications of EN156P-48-xxx (xxx=200-230) Series Poly-crystalline solar modules EN-156M-48-20 EN-156M-48-2 EN-156M-48-2 Module Type EN-156M-48-210 EN-156M-48-215 EN-156M-48-225 EN-156M-48-230 Maximum Power at 200Wp 205Wp 210Wp 215Wp 220Wp 225Wp 230Wp STC(Pmax) Maximum Power Voltage 24.73V 24.85V 24.97V 25.09V 25.26V 25.43V 25.59V (Vmp) Maximum Power Current (Imp) 8.09A 8.25A...
  • Page 20 5.5.Electrical specifications of EN156P-36 xxx(xxx=150-175) Series Poly-crystalline solar modules Module Type EN-156M-36-150 EN-156M-36-155 EN-156M-36-160 EN-156M-36-165 EN-156M-36-170 EN-156M-36-175 Maximum Power at STC(Pmax) 150Wp 155Wp 160Wp 165Wp 170Wp 175Wp Maximum Power Voltage (Vmp) 19.23V 19.38V 19.53V 19.70V 19.86V Maximum Power Current (Imp) 7.89A 8.08A 8.27A...
  • Page 21 5.6. Electrical specifications of EN156M-72- xxx (xxx=300-360)Series Mono crystalline solar modules EN156M-72- EN156M-72- EN156M-72- EN156M-72- EN156M-72- EN156M-72- EN156M-72- EN156M-72- EN156M-72- Module Type Maximum Power (Pmax) Maximum Power Voltage 37.65 37.93 38.21 38.51 38.7 38.94 39.14 39.32 39.62 (Vmp) Maximum Power Current 8.77 8.84 8.97...
  • Page 22 5.7. Electrical specifications of EN156M-60- xxx (xxx=275-305)Series Mono crystalline solar modules Module Type EN156M-60-275 EN156M-60-280 EN156M-60-285 EN156M-60-290 EN156M-60-295 EN156M-60-300 EN156M-60-305 Maximum Power (Pmax) Maximum Power Voltage 31.52 31.81 32.14 32.42 32.61 32.9 33.22 (Vmp) Maximum Power Current 8.73 8.81 8.87 8.95 9.05 9.12...
  • Page 23 5.8. Electrical specifications of EN156M-54- xxx (xxx=245-275)Series Mono crystalline solar modules Module Type EN-156P-54-245 EN-156P-54-250 EN-156P-54-255 EN-156P-54-260 EN-156P-54-265 EN-156P-54-270 EN-156P-54-275 Maximum Power at 245Wp 250Wp 255Wp 260Wp 265Wp 270Wp 275Wp STC(Pmax) Maximum Power Voltage 29.91V 30.14V 30.33V 30.54V 30.75V 30.93V 31.11V (Vmp) Maximum Power Current...
  • Page 24 5.9. Electrical specifications of EN156M-48- xxx (xxx=220-245)Series Mono crystalline solar modules Module Type EN-156P-48-220 EN-156P-48-225 EN-156P-48-230 EN-156P-48-235 EN-156P-48-240 EN-156P-48-245 Maximum Power at STC(Pmax) 220Wp 225Wp 230Wp 235Wp 240Wp 245Wp Maximum Power Voltage (Vmp) 26.01V 26.17V 26.35V 26.53V 26.73V 26.89V Maximum Power Current (Imp) 8.47A 8.60A 8.73A...
  • Page 25 5.10. Electrical specifications of EN156M-36- xxx (xxx=165-185)Series Mono crystalline solar modules Module Type EN-156P-36-165 EN-156P-36-170 EN-156P-36-175 EN-156P-36-180 EN-156P-36-185 Maximum Power at 165Wp 170Wp 175Wp 180Wp 185Wp STC(Pmax) Maximum Power Voltage 19.45V 19.69V 19.91V 20.12V 20.29V (Vmp) Maximum Power Current 8.47A 8.63A 8.79A 8.95A...
  • Page 26 5.11. Electrical specifications of EN156P-144- xxx (xxx=300-355)Series Poly crystalline solar modules EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- Module Type 144-300 144-305 144-310 144-315 144-320 144-325 144-330 144-335 144-340 144-345 144-350 144-355 Maximum Power (Pmax) Maximum Power Voltage (Vmp) 35.85 36.19...
  • Page 27 5.12. Electrical specifications of EN156P-120- xxx (xxx=250-295) Series Poly crystalline solar modules EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- EN156P- Module Type 120-250 120-255 120-260 120-265 120-270 120-275 120-280 120-285 120-290 120-295 Maximum Power ( Pmax ) Maximum Power Voltage (Vmp) 30.16 30.45 30.72...
  • Page 28 5.13. Electrical specifications of EN156M-144- xxx (xxx=345-395) Series Mono crystalline solar modules EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- EN156M- Module Type 144-345 144-350 144-355 144-360 144-365 144-370 144-375 144-380 144-385 144-390 144-395 Maximum Power (Pmax) Maximum Power Voltage (Vmp) 38.51 38.70 38.94...
  • Page 29 5.14. Electrical specifications of EN156M-120- xxx (xxx=290-300) Series Mono crystalline solar modules EN156M-120- EN156M-120- EN156M-120- EN156M-120- EN156M-120- EN156M-120- EN156M-120- EN156M-120- EN156M-120- Module Type Maximum Power (Pmax) Maximum Power Voltage 32.42 32.61 32.90 33.22 33.53 33.85 34.16 34.45 34.76 (Vmp) Maximum Power Current 8.95 9.05 9.12...
  • Page 30 5.15. Electrical specifications of EN158M-144- xxx (xxx=360-395) Series Mono crystalline solar modules EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 39.14 39.32 39.62 39.89 40.15 40.43 40.69 40.94 Maximum Power Current (Imp) 9.20 9.29 9.34...
  • Page 31 5.15.1 Electrical specifications of EN158M-144- xxx (xxx=360-395) Series Mono crystalline solar modules EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- EN158M-144- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 39.14 39.32 39.62 39.89 40.15 40.43 40.69 40.94 Maximum Power Current (Imp) 9.20 9.29 9.34...
  • Page 32 5.16. Electrical specifications of EN158M-120- xxx (xxx=295-330) Series Mono crystalline solar modules EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 32.61 32.90 33.22 33.53 33.85 34.16 34.45 34.76 Maximum Power Current (Imp) 9.05 9.12 9.19...
  • Page 33 5.16.1 Electrical specifications of EN158M-120- xxx (xxx=295-330) Series Mono crystalline solar modules EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- EN158M-120- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 32.61 32.90 33.22 33.53 33.85 34.16 34.45 34.76 Maximum Power Current (Imp) 9.05 9.12 9.19...
  • Page 34 5.17 Electrical specifications of EN158P-120- xxx (xxx=270-305) Series Mono crystalline solar modules EN158P-120- EN158P-120- EN158P-120- EN158P-120- EN158P-120- EN158P-120- EN158P-120- EN158P-120- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 31.35 31.71 32.05 32.33 32.64 32.91 33.20 33.52 Maximum Power Current (Imp) 8.62 8.68 8.75...
  • Page 35 5.17.1 Electrical specifications of EN158P-120- xxx (xxx=270-305) Series Mono crystalline solar modules EN158P-120 EN158P-120 EN158P-120 EN158P-120 EN158P-120 EN158P-120 EN158P-120 EN158P-120 Module Type -270 -275 -280 -285 -290 -295 -300 -305 Maximum Power (Pmax) Maximum Power Voltage (Vmp) 31.35 31.71 32.05 32.33 32.64 32.91...
  • Page 36 5.18 Electrical specifications of EN158P-144- xxx (xxx=330-365) Series Mono crystalline solar modules EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 37.73 38.04 38.31 38.55 38.81 39.10 39.39 39.64 Maximum Power Current (Imp) 8.75 8.81 8.88...
  • Page 37 5.18.1 Electrical specifications of EN158P-144- xxx (xxx=330-365) Series Mono crystalline solar modules EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- EN158P-144- Module Type Maximum Power (Pmax) Maximum Power Voltage (Vmp) 37.73 38.04 38.31 38.55 38.81 39.10 39.39 39.64 Maximum Power Current (Imp) 8.75 8.81 8.88...

  • Page 38: Disclaimer Of Liability

    PV produce, the specifications, or product information sheets without prior notice. 7. Contact us CHINA AUSTRALIA Econess Energy Co., Ltd Sunnygene Power Pty Ltd No.58 Haida Road, Huashi, Jiangyin, Jiangsu Province, China Level 2, 311 Lonsdale Street, Dandenong VIC 3175 214421 Email: Tony_Zhang@sunnygene.com.au...

This manual is also suitable for:

En125m-96 seriesEn156p-60 seriesEn156m-60 seriesEn156p-72 seriesEn156m-72 seriesEn156m-120 series ... Show all

Table of Contents