Subscribe to Our Youtube Channel
Related Manuals for Atlas Copco PHE 45 S
Summary of Contents for Atlas Copco PHE 45 S
- Page 2 Repair Instructions No.189.03/01 PAGE PHE 45 S Special Tools Torx screwdriver TX 1 4931 599 004 Require Torx screwdriver TX 20 4931 599 005 Torx screwdriverbit TX 30 4932 319 998 Permanent-magnet holder 4932 315 508 Forcing disks 4931 599 021...
- Page 3 Repair Instructions No.189.03/01 PAGE PHE 45 S Removing Loosen the four screws (B) and remove the armature the motor housing cap (A). Remove the respective brush springs (2) from the carbon brushes (D) and place them on the upper edge of the brush holder (E).
- Page 4 Repair Instructions No.189.03/01 PAGE PHE 45 S Detaching the Loosen the two screws (4) and remove the damping element gear box insulation (2) and (3). Undo both screws (5) of the handgrip holder (7) and remove them together with the discs (6).
- Page 5 Repair Instructions No.189.03/01 PAGE PHE 45 S Detaching the Lever off the cap (3) with aid of a screw- bearing end plate driver. Remove the distance sleeve (4) and the sleeve (5) from the machine. Remove the four screws (F). The screws are very tight, since they were secured with locking agent.
- Page 6 Repair Instructions No.189.03/01 PAGE PHE 45 S Dismantling the Loosen two screws (H). reduction gear Remove the bearing (G) and the reduction gear shaft assembly (E). If necessary, expel the reduction gear shaft assembly (E) with aid of a plastic hammer.
-
Page 7: Maintenance
Repair Instructions No.189.03/01 PAGE PHE 45 S Maintenance General It is recommended that maintenance be performed on the machine at regular intervals or when the carbon brushes switch off at the latest. Cleaning Clean all parts – with the exception of the electrical parts – with cold cleaning agent. Caution! No cleaning agent should penetrate into the bearing. - Page 8 Repair Instructions No.189.03/01 PAGE PHE 45 S Assembly Assembling the Mount the needle bearing (8) in the con- crank assembly necting rod (7). Push the piston (5) over the connecting rod (7) and mount the pin (6). Press the needle bearing (2) into the crank gear.
- Page 9 Repair Instructions No.189.03/01 PAGE PHE 45 S Assembling Lightly grease the inner wall of the cylin- the spindle der (4) and push it over the piston (O) (the piston is illustrated on page 7, pos.5, ill. 1). Insert the cylinder (4) with the percussion...
- Page 10 Repair Instructions No.189.03/01 PAGE PHE 45 S Mounting the Press the ball bearing (1) onto the crank crankcase gear. top cover Mount the locking ring (2) with aid of spe- cial pliers. Fit the crankcase top cover (3) and the gasket (7) to the crankcase.
- Page 11 Repair Instructions No.189.03/01 PAGE PHE 45 S Mounting the Insert a sleeve (4) into the handle shell (A) electric and fit the handle shell to the motor housing. components Mount the second sleeve (4) , the elec- tronic element (1), and the switch board (C) in the handle (6).
- Page 12 Repair Instructions No.189.03/01 PAGE PHE 45 S Mounting the Push the plug (5) over the armature (6) armature and press the fan (7) onto the arma- ture (6). Press the ball bearing (8) as well as the ball bearing (4) over the armature.
- Page 13 Repair Instructions No.189.03/01 PAGE PHE 45 S Mounting the Push the clamping plate (5) over the neck holding grip of the machine. Insert the nut (6) into the clamping plate (5). Push the pin (4) through the clamping plate (5) and the nut (6).
Need help?
Do you have a question about the PHE 45 S and is the answer not in the manual?
Questions and answers