Advertisement
Quick Links
Drawing①
①
hexagon screw M8*50
1.use M8*50 to connect bar table foot
and bar table face。
2.Link the sideling board between the
face and foot by screw CT-M5*50..
②
①
③
tapping screw CT-M5*50
③
Name
Item No.
Quantity
2pcs
①
bar table foot
1pcs
②
bar table face
4pcs
③
Bar sideling board
4pcs
hexagon screw M8*50
8pcs
tapping screw CT-M5*50
Advertisement
Related Manuals for Alpine Spas Gazebo
Summary of Contents for Alpine Spas Gazebo
- Page 1 Name Item No. Quantity Drawing① 2pcs ① bar table foot 1pcs ② bar table face 4pcs ③ Bar sideling board 4pcs hexagon screw M8*50 8pcs tapping screw CT-M5*50 ② ① ③ tapping screw CT-M5*50 ① ③ hexagon screw M8*50 1.use M8*50 to connect bar table foot and bar table face。...
- Page 2 Drawing② The 4 corners can be employed universally. The shutters and below blanking plate can be employed universally.
- Page 3 Name Item No. Quantity Drawing③ 4pcs corner ① 2pcs ② blind window flange bolt M8*80 bottom seal plate 2pcs ③ bar table 1pcs ④ beam 2pcs ⑤ flange nut M8*80 40pcs hexagon screw M8*50 12pcs tapping screw CT-M5*50 ① ② ⑤...
- Page 4 Drawing④ tapping screw CT-M5*50 Big roof 8 Big roof 7 1.Link 4 PS 1.97M parts and tripods with gazebo body by screw CT-M5*50.
- Page 5 Drawing⑤ Keep the contact surface flat The left backbone A The sink hole is at the above The left big roof Screw CT - M5*50 The left crossband A The right backbone The sink hole is at the above The right following crossband The right big roof 1.The left big roof:: Put the long and short crossband with left following crossband A to the neck in the middle board and left backbone A.
- Page 6 1.Link two frames of big roof by Gazebo body screw M8*90, then become four pairs by eight frames. Put the big roof on the gazebo, 2.Put two big roof on the gazebo then keep the level with gazebo body. body.
- Page 7 Screw CT-M5*60 Drawing⑦ Screw CT-M5*60 Screw M8*80 Put the big roof on the gazebo, 1.Put the orther 3 big roof on the then keep the level with gazebo body. gazebo, then combine them by screw M8*80 as picture. 2.Link the big roof with the frame on the gazebo body.
- Page 8 Drawing⑧ keep the contact surface flat Screw CT-M5*50 big roof 6 The neck location Big roof 1 Big roof 3 Big roof 2 Big roof 5 Big roof 4 1 . Put the small frame on the big roof, then put the middle board to the neck of the frame, lock them by screw CT - M5*50.
- Page 9 screw DB-M4*25 Drawing⑨ 90°hardware Straight hardware 1.Put the 90°hardware on the corner connection of big roof, lock them by screw DB-M4*25. 2.Put the straight hardware on the middle connection of big roof, lock them by screw big flat screw DB-M4*25.
- Page 10 The right big roof 2.The middle line of top roof should be at be at side or inside of gazebo, then install the the middle of big roof frame. orther three top roof on the frame.
- Page 11 DB-M4*50 white shim 1,Put the small roof on the gazebo top from the big roof frame, them put the 151°hardware under big roof inside frame, lock them by screw DB-M4*25 . 2,Put 4pcs tillers to the big roof , lock them by screw DB-M4*50 abd white shim.
- Page 12 Name Item No. Quantity Drawing⑿ 8pcs short round bar ① middle length 4pcs ② round board the surface of pole key mapping should be the surface of pole key mapping should be 4pcs ③ long round bar the same level with that of bar foot. the same level with that of bar foot.
Need help?
Do you have a question about the Gazebo and is the answer not in the manual?
Questions and answers