Me TS-D200 Series User Manual

Me TS-D200 Series User Manual

5w transceiver

Advertisement

TS-D200 / me-D350 range
User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TS-D200 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Me TS-D200 Series

  • Page 1 TS-D200 / me-D350 range User Guide...
  • Page 2: Table Of Contents

    Contents Introduction ........................2 Preparing for use ......................2 Description of modem ..................2 Features ......................3 External connections ................... 3 DB-15 Pin Interface ..................... 4 Channel selection ....................6 Operation ........................6 Transmit/receive operation .................. 6 Serial commands....................6 Commands and data ...................
  • Page 3: Introduction

    Introduction The TS-D200/me-D350 range is a 1 to 5 Watt radio data modem, which can be used for data up to 9600 baud rate (using GMSK module) in stand alone conditions. The TS-D200/me-D350 is housed in a rugged cast-aluminium box sealed to IEC 529 (IP54) making it suitable for a wide range of mobile and fi...
  • Page 4: Features

    Features ● Frequeny Banda VHF2: 146 - 174MHz UHF1: 400 -440MHz UHF2: 440 - 480MHz ● Compact and rugged die cast box ● Resistant to dirt, dust and water ingress (IP54 rated) ● Network free, point to point communication ● 1/5 watt programmable output power ●...
  • Page 5: Pin Interface

    DB-15 Pin Interface Connector BUSY RS232 DATA OUT (OPT) DATA MOD IN MIC IN (AF) SERIAL BUSY OUT (OPT) Data OUT (AF) SERIAL IN (PROG.) GPS DATA IN (OPT) PTT IN SPK OUT +VE IN / RS232 DATA (OPT) GPS DATA OUT (OPT) SERIAL OUT (PROG.) The table on the following pages indicates the DB-15 Pin descriptions with input and output levels.
  • Page 6 Pin No Function Description Signal Type RSSI RSSI Level 1.0 to 3.5 V Link option Program data IN / Used for serial command for radio TTL level Serial command control or is used for inputting (RS232 converter in programming data programming cable) Audio OUT Audio output from the audio amplifi...
  • Page 7: Channel Selection

    Operation Transmit/receive operation The TS-D200/me-D350 can be put into transmit by different methods. When used as a “dumb” radio, the PTT line is pulled low (pin 3 of DB15). The TX serial command will also put the radio into transmit (pin 8 of DB15), until the RX serial command is received. If the Mic line is low (grounded via resistor) then audio on the Mic line is transmitted and if line is left disconnected DATA is transmitted.
  • Page 8: Commands And Data

    Response format: DATA1 DATA2 DATAn The response CMD is in the form of: ACK, acknowledge, Hex: 0xAA; (then data if any) NACK, no acknowledge (error in command) Hex: 0x55 NOK, not okay (cannot carry out command) Hex: 0x65 If command is not recognised, if it is repeated, or already in requested or wrong state (e.g.
  • Page 9 Mode Transmit Transmit Response Response Data Remark command Data (DATA) (CMD) (CMD) Scan start, 0x62 0x73 0X66 Chn no., Respond once if stopped whist stopped CMD+DATA on a channel. e.g.If on on ‘correct call’ channel 1 : 66,00,66 channel (00=chn1,01-chn2) Scan Stop 0x62 0x46...
  • Page 10: Standard Radio Commands

    Standard radio commands Scanning A scan function is available whereby any or all 16 channels can be monitored for activity. Scanning parameters such as scan speed and delay are programmable (refer to programming guide) Control of the scan channels is by serial commands. Note The priority channel (the transmit channel during scanning) is the channel selected via the dip switch.
  • Page 11: Status Indicators And Audible Alerts

    Status indicators and Audible alerts The LED indicates the current status of the radio and if an external speaker is connected to pin 9 of the DB-15, audible tones can be heard under certain fault conditions. The details are shown in the table opposite. Audible tone Status Description...
  • Page 12: Programming

    Fixing We recommend that the TS-D200/me-D350 is securely fi xed to a surface, either directly, or with a suitable bracket. The fi xing hole centre dimensions are as shown. The modem can be attached to any surface by using suitable size screws through the M3.5 holes in the mounting fl...
  • Page 13: Safety And General Information

    Safety and general information Important information on safe and effi cient use of your Radio device Exposure to radio frequency energy Your modem is a high power radio transceiver. When it is on, it receives and also sends out radio frequency (RF) signals. To help minimise human exposure to RF electromagnetic energy, keep transmission time to 50% or less.
  • Page 14: Warranty And Repairs

    Do not over tighten connection to the modem. Disposal / Recycling The TS-D200/me-D350 is a Class 3 product in accordance with the Waste of Electrical and Electronic Equipment (WEEE) Directive. Disposal of this class of equipment must be carried out through an authorised recycling centre.
  • Page 15: Declaration Of Conformity

    Declaration of conformity* The TS-D200/me-D350 range is a 1 to 5 Watt radio data modem, in V2 (146-173MHz), U1(400-440MHz) or U2 (440-480MHz) frequency ranges, These frequencies are licensed, restriction of use may apply in some countries. This equipment is intended for use in:-...
  • Page 16: Red2014/53/Eu European Specifi Cations

    RED2014/53/EU Specifi cations Art. 3.1 (a) Health & Saftey EN60950-1:2006+A2:2013 EN62368-1:2014 EN62311:2008 Art. 3.1(b) EN301 489-1 V2.2.0 Draft EN301 489-5 V2.2.0 Draft Art. 3.2 Radio EN300 113 V2.2.1(2016-12) EN300 113-2 V1.4.2(2009-11) EN300 113-1 V1.6.2(2009-11) EN300 220 V2.1.2(2007-06) We hereby declare that the above named product is in conformity to all the essential requirements of the Radio Equipment Directive (RED2014/53/EU).

This manual is also suitable for:

Me-d350 series

Table of Contents