Related Manuals for Fujitsu Plasmavision PDS6101W-H
Summary of Contents for Fujitsu Plasmavision PDS6101W-H
- Page 1 PDS6101W/E-H PDS6101W/E-S F U J I T S U G E N E R A L P r o p r i e t a ry C o p y P r o h i b i t e d...
-
Page 2: Specifications
SPECIFICATIONS Power requirement 100-240V, 50/60Hz Environment (Operating) Current drain 7.5A Temperature 0 to 40 C Relative humidity 20 to 80% Display panel Pressure 850 to 1,114 hPa Screen size 131.1 (W) x 76.0 (H) [cm] 53.1 (W) x 29.9 (H) [inch] Accessories User's manual Aspect ratio... - Page 3 SETTING SIGNALS This display can store parameter settings for eight additional signals for RGB. To do this, select the desired signal and follow "RGB MODE ADJUSTMENT" in the manual to adjust the parameters. When you finish, the settings will be automatically stored. FACTORY SET SIGNALS (RGB MODE) Main corresponding signals (RGB mode) Display (dots x lines)
- Page 4 PART NAMES AND FUNCTIONS Remote contr ol Front VIDEO VIDEO VIDEO VIDEO MENU MENU MENU MENU ENTER ENTER ENTER ENTER SHIFT SHIFT SHIFT SHIFT Power indicator lamp This lamp shows the state of the power supply. Power ON button [POWER ON] Lit (red): Power OFF (stand-by) Turns the power ON.
- Page 5 TROUBLESHOOTING USING LED AND OSD 1. Display (1) OSD Two kinds of error messages are displayed on the screen, and the power is turned off 10 sec later. (2) LED LED error is displayed continuously after the power is turned off. 2.
- Page 6 AND V ADJUSTMENT When the Main Power Supply PCB and PDP panel are replaced, Vs and Vd must be adjusted. Adjustment time Within 3 minutes after power on. Adjustment signal Adjust the Vs and Vd in the no-signal state. Check points Refer to the drawing shown below. Adjustment points Refer to the drawing shown below.
- Page 7 DISASSEMBLY PROCEDURES DISASSEMBLY PROCEDURES DISASSEMBLY PROCEDURES DISASSEMBLY PROCEDURES 1.Removing the Rear Case 1) Remove the 35 circled screws and remove the Rear Case. * Layout of Main PCB. B C D B: Main Digital PCB A: Main Power PCB C: Video PCB D: Audio PCB - 19 - - 19 -...
-
Page 8: Parts List
PARTS LIST Ref.no. Description PDS6101W-H PDS6101E-H PDS6101W-S PDS6101E-S Cabinet Case Front 8113312003 8113386004 Case Rear 8113294002 Electric Fan Motor 8900295007 Optical Filter 8113178005 Audio PCB Assy 8113276008 Connection PCB Assy 8113282009 I/O PCB Assy 8113284003 Key Switch PCB Assy 8113280005 LED/PHOTO PCB Assy 8113278002 Main Digital PCB Assy 8113102000... - Page 9 TRANSPORTATION AND HANDLING RESTRICTIONS Transportation Bad loading Don't load the plasmavision on a truck as shown in the drawing. Handling Never topple. Never drop. Drop Over 20 cm Floor Don't hold the surface of the optical filter. - 60 -...
- Page 10 Don't stack the plasmavision over two units high. Example of good transportation and handling Good loading Load the plasmavision as shown above. - 61 -...
- Page 11 2. Removing the Main Power PCB 1) Remove the Rear Case. 2) Disconnect the circled connector. 3) Remove the 5 screws and Main Power PCB. * View after Main Power PCB removed.
- Page 12 3. Removing the Main Digital PCB (1 of 2) 1) Remove the Rear Case. 2) Remove the Video Unit. 3) Remove the 8 screws and Main Digital Shield Bracket. 4) Disconnect the circled connector.
- Page 13 3. Removing the Main Digital PCB (2 of 2) 5) Remove the 7 screws and connection PCB. 6) Remove the Main Digital PCB. * View after Main Digital PCB removed.
- Page 14 4. Removing the Audio PCB 1) Remove the Rear Case. 2) Remove the 6 screws and Audio Shield Bracket. 3) Disconnect the circled connector. 4) Remove the 3 screws. * View after Audio PCB removed.
- Page 15 5. Removing the PDP Unit (1 of 3) 1) Remove the Rear Case. 2) Remove the 8 screws and Main Digital Shield Bracket. 3) Disconnect the circled connector. 4) Remove the Base Frame from the Front Case together with panel and PCBs. * View of removal of the Base Frame from the Front Case.
- Page 16 5. Removing the PDP Unit (2 of 3) * View after the Front Case Panel Unit and PCBs removed. 5) Disconnect the circled connector. 6) Remove the 9 circled screws. 7) Disconnect the circled connector 8) Remove the 12 circled screws.
- Page 17 5. Removing the PDP Unit (3 of 3) * View after the PDP Unit Frame and PCBs removed. * View after only the PDP Unit removed. * Replaced the parts which are already mounted correctly, when the PDP Unit is replaced.
- Page 18 6. Removing the Video PCB * The Video PCB can be removed without moving the Rear Case. 1) Remove the 2 circled screws. 2) Pull out the Video PCB Unit from the Plasmavision. 3) Remove 5 screws from the Video PCB Unit. Note: Three kinds of screws are used on this Video Unit.
-
Page 19: Troubleshooting Flowchart
TROUBLESHOOTING FLOWCHART LED lamp blinking Note : 1. Protector operates when connector P4(CN4) is disconnected and power is turn off. Turn power on and check state of lamp. LAMP STATE POWER SUPPLY STATE REMEDY ∗ Replace Power Power supply Not lighted. circuit faulty. - Page 20 Check 1 Power supply protector operated Power lamp : Flashing continuously in red. Start (at an interval of 0.5 sec) (1) Turn the main power off and disconnect the connector P2,P3,P4,P5 and P6 on the Main Power PCB. (2) Connect pin 1 and pin 13 of P2 through a 1/4W, 1kΩ resistor. Connect pin 1 of P4 and pin 9 of P6 Turn the main power on again.
- Page 21 Check 2 Check 3 Fan protector operated Temperature protector operated Power lamp: Flashes once intermittently in red. Power lamp : Flashes intermittently twice in red. (For 0.5 sec. at an interval of 3 sec.) (For 0.5 sec. at an interval of 5 sec.) Start Start Is voltage at...
- Page 22 Check 4 RGB input is abnormal. Start Power lamp: Lighted green (10 sec or more) Is RGB Is RGB Is RGB Is RGB cable pin arrangement cable pin arrangement cable pin arrangement cable pin arrangement Check connection cable. appropriate ? appropriate ? appropriate ? appropriate ?
- Page 23 RGB 2 input term inal (R GB 2 INPUT/mD-sub) Connect this terminal to the PC’s display (analog RGB) output terminal or decoder (digital broadcast tuner, etc.) output terminal. RGB 1 input terminal (RGB 1 INPUT/DVI-D) Connect this terminal to the PC’s display (digital RGB) output terminal molex Inc.
- Page 24 FACTORY SET SIGNALS (Component video mode) FACTORY SET SIGNALS (Video, S-video mode) Horizontal Vertical Horizontal Vertical Signal Signal frequency (kHz) frequency (Hz) frequency (kHz) frequency (Hz) 15.73 59.94 SDTV 480i 15.73 59.94 NTSC 15.63 50.00 SDTV 576i 15.63 50.00 31.47 59.94 SDTV 480p 15.63...
- Page 25 C O N T E N T S IMPORTANT INFORMATION ........2 SPECIFICATIONS .
- Page 26 IMPORTANT INFORMATION WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Please use a screen saver to prevent burning of an after-image on the screen. Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety.
- Page 27 Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Have all service done by qualified service personnel. Unplug this unit from the wall outlet and have it serviced by qualified service personnel in the following cases: a) If the power supply cord or plug is damaged.