1. Manuals
  2. Brands
  3. Stern Engineering Manuals
  4. Toilets
  5. JUPITER 2030
  6. Installation and maintenance manual

Stern Engineering JUPITER 2030 Installation And Maintenance Manual

Electronic flush valve for urinal
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTALLATION AND MAINTENANCE GUIDE
ELECTRONIC FLUSH VALVE FOR URINAL
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JUPITER 2030 and is the answer not in the manual?

Questions and answers

Summary of Contents for Stern Engineering JUPITER 2030

  • Page 1 INSTALLATION AND MAINTENANCE GUIDE ELECTRONIC FLUSH VALVE FOR URINAL...
  • Page 2 INDE X TECHNICAL DATA PACK CONTENTS PRE-INSTALLATION INFORMATION INSTALLATION SETTINGS ADJUSTMENT BATTERY REPLACEMENT INSTRUCTIONS MAINTENANCE Filter cleaning instructions Care and cleaning of chrome and special finishes SPARE PARTS LIST LIMITED WARRANTY SERVICE CHECK LIST...

  • Page 3: Datos Técnicos

    DATOS TÉCNICOS JUPITER 2030 JUPITER 2030 E Power Supply: 9V battery or 9V transformer Operating water pressure: 0.5-8.0 bar. 24 hours automatic flush when not used to improved hygiene. Sensor range: 600 mm. Factory set. Adjustable manually or with a remote control.

  • Page 4: Pack Contents

    1 x Temporary protective panel 1 x Plastic seat for the cover plate 1 x Allen key 4 x Screws 1 x Wall cover plate with the electronic unit and battery box 1 x M4x10 Screw JUPITER 2030 E 1 x Transformer...

  • Page 5: Pre-Installation Info

    PRE–INSTALLATION INFO Check contents Separate all parts from packaging and check each part with the pack contents section. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install the electronic flush valve until you obtain the missing parts.

  • Page 6: Installation

    7) Assemble the temporary protective cover to protect the flush valve. Step 2 – Connecting the water supply and the power source 1) If your model is Jupiter 2030 E, place the transformer near the electricity plug, insert the transformer cable wire through the box.
  • Page 7 5) Assemble the panel to the cover seat and tighten it with the bottom screw. 6) Now, remove the protecting sticker that covers the sensor. 7) If your model is Jupiter 2030 E, plug the transformer. Important: After connecting the power source, wait a few seconds before activating the flush valve to avoid entering into “adjusting mode”.

  • Page 8: Se T T Ings Adjustment

    SE T T INGS ADJUSTMENT Adjusting the sensor settings with a remote control – optional and recommended: In order to adjust the sensor with a Remote Control you should hold the Remote Control straight in front of the sensor in a distance of about 6-8” (15-20cm). Choose the function you want to adjust by pressing once on one of the function buttons.

  • Page 9: Range Adjustment

    1. Disconnect the battery or switch off the electricity supply to the sensor. 2. For Jupiter 2030, make a short circuit between the (+) and the (-) connections of the sensor. A screw driver or any conductive material can be used to make this short circuit.

  • Page 10: Maintenance

    0 7 0 4 0 1 1 8 Sensor Kit for Jupiter 2030 0 7 2 2 0 0 1 2 Sensor Kit for Jupiter 2030 E 0 7 2 2 0 0 1 3 Solenoid Valve Kit with Acetal Body...

  • Page 11: Troubleshooting

    TROUBLE – SHOOTING P R O B L E M I N D I C AT O R C A U S E S O L U T I O N Sensor flashes continuously when Low battery. Replace battery. user’s steps within the sensor’s range.

This manual is also suitable for:

Jupiter 2030 e

Table of Contents