RCA RDR670 Owner's Manual page 11

Operation
Drying a load of laundry
Cycle Fabric type Dryness Level Temp Delay
Very Dry
More Dry
Cotton
● ●
Normal Under wear Normal High
Linen
Less Dry
Damp Dry
Very Dry
More Dry
Sensitive ● ●
Delicates Normal Low
items
Less Dry
Damp Dry
Very Dry
Wrinkle-free
More Dry
cottons
● ●
Casual synthetic Normal Medium
fabrics
Less Dry
knits
Damp Dry
Very Dry
More Dry
Towels
●
Towels Heavy Normal High
cottons
Less Dry
Damp Dry
Bedding
● ●
Sanitize Very Dry High
Curtains
Very Dry
More Dry
Jeans
●
Heavy Duty Corduroys Normal High
Work clothes
Less Dry
Damp Dry
Very Dry
More Dry
Blankets
● ●
Bulky Sheets Normal Medium
Comforters
Less Dry
Damp Dry
High
Medium
●
Quick Dry Low
Ultra low
No heat
High
Medium
●
Time Dry Low
Ultra low
No heat
● ●
Air fluff No heat
* Table in grey is an initial setting. Dots are all optional functions you can select.
Load Size Recommendations:
For best results, follow the wet load size
recommendations noted for each cycle.
Small load: Fill the dryer drum with
3-4 items, not more than 1/4 full.
Wrinkle Time Default time Default time Maximum
My Cycle
Prevent adjust (Gas) (Elec.)
●
50min 50min
●
34min 34min
●
27min 27min
● ●
58min 58min
●
60min 60min
● ●
62min 62min
●
62min 62min
● ● ●
30min 30min
● ● ●
40min 40min
● ●
20min 20min
Medium load: Fill the dryer drum up
to about 1/2 full.
Large load: Fill the dryer drum up to
about 3/4 full. Do not overload. Items
need to tumble freely.
19
Operation
Drying a load of laundry
STEP 4: Set Delay Start
Amount
STEP 5: Start your dryer
STEP 6: Unloading your laundry
Note: You can skip this step if you don't want this function.
- You can set a period time in hours to delay your drying operation.
- Press the "Delay" button once to enter the delay start setting
function with the digital displaying your last setting time plus one
more hour or "1" for initial setting
Delay
- Press the "Delay" button every time, the delay start time in hours
displayed will change in sequence: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, then change to
cycle setting display.
Or, you can press and hold the "Delay" button to quickly adjust the
setting time until your desired time displayed.
- Select your desired delay start time. The delay light will be ON.
- When "24" is displayed, press
the function.
Notes:
- If you don't press any button when you are setting delay start time
in 3 seconds, the dryer will back to cycle and option setting with
remaining time displayed with "Delay" light ON. Press the button
"Delay" again will back to delay setting with "Delay" light flashing.
- If you want to change your cycle setting when you are setting delay
start time, just rotate the knob or press relative option buttons. The
display will change to remaining time for selected program with
"Delay" light ON.
- Any time, if you press the "Delay" button, the display will show the
setting delay start time with one more hour.
- The delay start time cannot be changed after the appliance
started except powering off the unit.
Now, it's time to start your dryer.
- If you have set your desired Delay Start time, the "Delay" light will
be ON and your dryer will start to count down the delay start time.
- If you don't have any delay start setting or the delay start time has
been finished, the unit will start your selected program. The relative
process light will flash accordingly.
Notes:
You can just press the "Power" button to turn your dryer OFF and
then press again to turn it ON to cancel the Delay Start function.
- When you do so, this will reset your setting program.
Any time you pause the unit or open the door, you should press the
"Start/Pause" button to resume the operation.
- The "Clean filter" light in the process bar will flash when your
laundry load has been finished.
- The dryer will beep 6 times after the cycles done.
- You should clean the filter after every load once the laundry is
unloaded. For detail, refer to page 21.
20
with "Delay" light flashing.
"Delay" button once more to cancel