Table of Contents
Advertisement
All operators must fully read and understand
this operator's manual before using the chipper.
Keep this manual for future reference.
HANSA NEW ZEALAND
+64 7 849 4749
www.hansaproducts.co.nz
Operation, maintenance and safety manual
info@hansaproducts.co.nz
HANSA AUSTRALIA
1800 426 722
www.hansaproducts.com.au
info@hansaproducts.com.au
Advertisement
Table of Contents
Summary of Contents for Hansa F3 CHAFF CUTTER
- Page 1 Operation, maintenance and safety manual All operators must fully read and understand this operator’s manual before using the chipper. Keep this manual for future reference. HANSA NEW ZEALAND HANSA AUSTRALIA +64 7 849 4749 info@hansaproducts.co.nz 1800 426 722 info@hansaproducts.com.au www.hansaproducts.co.nz...
-
Page 2: Table Of Contents
YRE PRESSURE ..................................... 13 OLT TORQUE SPECIFICATIONS ..................................13 DECALS ....................................... 14 HANSA GLOBAL INDUSTRIAL LIMITED WARRANTY ........................15 COMMISSIONING CHECKLIST AND REGISTRATION ........................17 Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 3: What Can My Hansa Chaff Cutter Process
What can my Hansa chaff cutter process? Intended uses of the chaff cutter The Hansa F3 chaff cutter is built to process animal feed and light organic material. Do NOT use the machine for any other purpose. Suitable feed materials include:... -
Page 4: Assembly
Do NOT allow persons to operate the machine without full and proper instruction in the use and safe operation of the chaff cutter and maintenance as detailed in this manual. Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 5: Ambient Conditions
Do not use the machine if the switch does not turn it on and off. Any machine that cannot be controlled with the switch is dangerous and must be repaired. Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 6: Service
Do NOT look in to, or put your face near the outlet, even when the machine is turned off Do NOT put the machinery in a place where material output might be obstructed Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 7: Operation
Exercise caution when feeding material into the machine, especially when the length of material is short Do NOT use your hands to feed material in past the safety guard Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 8: Power Supply
Power supply The F3 chaff cutter requires a 220-240V AC 50Hz earthed power connection. The chaff cutter is rated at 8.4 A. It is recommended that the chaff cutter is only connected to a power socket which is protected by a circuit-breaker that would activate with a residual current not more than 30 mA. -
Page 9: Controls
Transportation The F3 Chaff Cutter is designed to be moved by one person using the handles at the top of the inlet chute to lean the machine backwards and transfer its weight onto the wheels. The chaff cutter can then be wheeled to and from the work location. -
Page 10: Troubleshooting
Z51 v-belts. To inspect the belts, remove the pulley guard (see step 1 of ‘Maintaining the chain drive’ below). Split belt cover Soft, swollen belt Cracked underside of belt Worn cover on back of belt Sidewall belt wear Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 11: Maintaining The Chain Drive
When putting the front chain back on, check that the tensioner drum is in the right position. You should not be able to take the chain off the sprockets when the tensioner is in the correct position. Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 12: Greasing The Bearings
Typically the cutting reel of your Hansa chaff cutter will not require sharpening as often as the base blade. The reel blades are made from hardened steel, so under normal circumstances the cutting reel will maintain its sharp edge for hundreds of hours of use. -
Page 13: Cutting Mechanism Checking/Adjustment
Make sure plenty of coolant is used when grinding to avoid softening of the base blade. If you don’t have a surface grinder or are unsure how to re-sharpen the base blade, contact a professional saw doctor or Hansa to arrange re-sharpening. - Page 14 Torque the reel adjustment plate bolts to 44 Nm. After doing so, check that the position of the reel hasn’t changed by running more paper through the cutting mechanism. Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019...
-
Page 15: Tyre Pressure
Reattach all guards to the swing arm. Sharpening the reel If the edges of the reel are considerably worn/rounded, contact a professional saw doctor or Hansa to arrange re-sharpening. Tyre pressure The maximum recommended tyre pressure is 25 Psi. Over inflation may cause tyre to rupture. -
Page 16: Decals
Decals Decal Description Location General machine safety Top of pulley guard, next to E-stop Bonnet safety Side of pulley guard, next to lockout switch tab Hansa F3 Chaff Cutter O&M Manual - OM-016 Revision B 14/05/2019 © Hansa Products 2019... -
Page 17: Hansa Global Industrial Limited Warranty
HANSA offers a special extended warranty period (“Extended Warranty”) to new HANSA products purchased from an authorised HANSA dealer. The Extended Warranty period is set out below. In order to take advantage of the Extended Warranty you must: 1. Register your HANSA product through the HANSA warranty registration process and identify your HANSA product by its machine serial number. - Page 18 General 1. Your rights: a. HANSA will recognise any implied rights and remedies that are available to you at law in the applicable territory and that cannot be excluded by HANSA. b. In New Zealand, Hansa Products Ltd will recognise your statutory rights under the Consumers Guarantee Act 1993 (provided that you are a consumer for the purposes of that Act).
-
Page 19: Commissioning Checklist And Registration
Commissioning checklist and registration It is the retailers’ responsibility to ensure that this chipper is correctly commissioned for use, and that the purchase is registered with Hansa Chippers so as to provide the owner with the full benefit of the warranty policy.
Need help?
Do you have a question about the F3 CHAFF CUTTER and is the answer not in the manual?
Questions and answers