Table of Contents
Advertisement
Quick Links
Please read these instructions completely before proceeding with installation.
The oil level in the compressor must be checked BEFORE running the engine or
compressor. Failure to do so will result in a faulty compressor and a void warranty.
Front View
Item Description
A
Compressor
B
Serpentine Belt (with air)
C
Serpentine Belt (without air)
D
Alternator Pulley
E
Clutch/Pulley Assembly
F
Idler/Pulley Assembly
G
Overflow Reservoir
H
Coelescing Filter
I
Inlet Filter
J
Leader Hose
K
Computer Bracket
L
Compressor Plate
M
Coolant Reservoir Bracket
N
Upper Bracket
O
Lower Left Bracket
P
Lower Right Bracket
Q
Air Filter Bracket
R
Brass Cross Bracket
S
Compressor Fitting
T
Compressor Sleeve Insert
U
O-ring
V
1
/
" NPT Check Valve
2
W
1
/
" NPT Relief Valve
4
X
110-145 p.s.i. Pressure Switch
1
1
Y
/
" NPTM x
/
" Tube Straight
2
2
1
1
Z
/
" NPTM x
/
" NPTF Bushing
2
4
AA
1
/
" Brass Cross
2
BB
Plug
CC
1
/
" NPTM x
1
/
" NPTF Bushing
2
8
DD
1
/
" NPTF Coupling
2
Air Commander
Part No. 27325, with air
Part No. 27332, without air
www.airliftcompany.com
Important Warranty Information
1. If the compressor or engine is run without having
2. If the belt is misinstalled or the belt does not
3. Failure to use included installation components
4. Failure to check proper oil level and conditions
5. This compressor must only be used in an air
Side View
Installation Components
Part Number
Qty.
Item Description
EE
24325
1
FF
10652
1
10655
1
GG
10230
1
HH
26615
1
II
JJ
26630
1
KK
21135
1
LL
21107
1
10670
1
MM
22024
1
NN
10730
1
OO
PP
10755
1
QQ
10179
1
RR
10761
1
10762
1
SS
10763
1
TT
10479
1
UU
VV
26237
1
WW
21130
2
XX
21125
2
21578
2
YY
21285
1
ZZ
24290
1
AB
24551
1
AC
AD
21369
5
AE
21247
1
21221
1
AF
21190
1
AG
21251
1
AH
21220
3
AI
T echnical Support
1-800-248-0892
Ext. 2
oil in the compressor, then the warranty is void.
have the proper tension, then the warranty is
void.
properly voids the warranty.
will void the warranty.
compressor application only, not an air
conditioning application. No freon is required.
1
/
" Street Tee
2
3
3
/
"-16 x
/
" Bolt
8
4
3
/
" Flat Washer
8
3
/
"-16 x 1 Carriage Bolt
8
3
/
"-16 x
7
/
" Bolt
8
8
3
/
" Lock Washer
8
3
/
"-16 Hex Nut
8
8mm-1.25 x 25mm Bolt
8mm Flat Washer
8mm Lock Washer
Frame Clamp
1
/
"-20 x .75" Bolt
4
Self Tapper
5
/
" Flat Washer
16
10-32 x
3
/
" Machine Screw
8
1
/
"-20 Kep Nut
4
1
/
" Hose Clamp Worm
4
20 amp AGC Fuse
Red 16 Gauge Wire
ATC/ATO Fuse Tap In
Mini Fuse Adapter
Butt Connector
1
/
" Female Terminal
4
AGC Fuse Tap In
3
/
" Female Terminal
16
Thread Sealant
1
/
" Nylon Hose
2
Hose Cutter
Oil Dipstick
Pipe Nipple
MN-494
(02204)
ECN 3827
Part Number
Qty.
21391
1
17101
2
18444
9
17134
4
17187
3
18427
7
18430
4
17177
1
18501
1
18503
1
10181
1
17175
8
17102
2
18405
6
18496
2
18452
8
10550
1
24739
1
24643
8'
24542
1
24561
1
24645
2
24594
3
24543
1
24524
1
23586
2
20966
15'
10530
1
10159
1
21729
1
1
Advertisement
Table of Contents
Summary of Contents for Easystreet Air Commander
- Page 1 Air Commander MN-494 (02204) ECN 3827 Part No. 27325, with air Part No. 27332, without air www.airliftcompany.com Please read these instructions completely before proceeding with installation. The oil level in the compressor must be checked BEFORE running the engine or compressor.
- Page 2 T echnical Support 1-800-248-0892 Ext. 2...
-
Page 3: Assembling The Compressor
NOTE: This compressor will mount on the right (passenger) side of the engine. It may be necessary to relocate or remove the air conditioning lines. If the oil is low in the compressor, use Polyol Ester (P.O.E.) P.A.G. oil and fill to specified amount. I. -
Page 4: Preparing The Vehicle
II. Preparing the Vehicle 1. Remove the belt, belt tensioner, positive battery cable, back and side alternator bolts, computer and bracket, and radiator overflow. 2. It will be necessary to slightly bend the inner fender to obtain adequate clearance for the compressor. Use a pry bar or a 2 x 4 and pry using the frame (Figure 6). -
Page 5: Installing The Compressor
III. Installing the Compressor 1. Remove and replace the alternator pulley with the new pulley (D) supplied. 2. Set the assembly unit in place. If the compressor still hits, remove the assembly and adjust the fender. 3. Insert the carriage bolt protruding from the compressor mounting plate through the top bracket. -
Page 6: Checking The Belt
V. Installing the Radiator Overflow Reservoir 1. Remove the two bolts on the ABS/brake bracket on the driver side fender (Figure 14) and attach the bracket (M) to the ABS brake bracket using existing bolts removed. 2. Loosely attach the reservoir (G) to the bracket using bolts (PP), flat washer (RR), and nuts (TT). -
Page 7: Checking The Oil
VIII. Installing the Hose Assembly 1. Install the brass cross bracket (AA). Using the bracket (R) as a template, mark and drill the two " mounting holes and attach using two bolts (PP) and two nuts (TT). 2. Attach the bushing (CC) and pressure switch (X) to one leg of the brass cross (AA) and plug (BB) to the other leg directly across from the pressure switch (Figures 1 and 16). -
Page 8: Wiring The Electrical System
X. Wiring the Electrical System 1. The hot lead to the compressor is the black wire on the clutch. Cut off the fitting on the end of the black wire and using butt connector (ZZ), splice a length of the red wire (WW) to the black wire. Run red wire to spade terminal on the pressure switch. - Page 9 T echnical Support 1-800-248-0892 Ext. 2...
- Page 10 Thank you for purchasing Air Lift Products Mailing Address: Street Address: AIR LIFT COMPANY AIR LIFT COMPANY P.O. Box 80167 2727 Snow Rd. Lansing, MI 48908-0167 Lansing, MI 48917 Local Phone: (517) 322-2144 Fax: (517) 322-0240 www.airliftcompany.com For Technical Assistance call 1-800-248-0892 “The Choice of the Professional Installer”...
Need help?
Do you have a question about the Air Commander and is the answer not in the manual?
Questions and answers