Advertisement
Do not use this equipment before reading this manual!
TS / TSR
(Turbine System)
Pro-Finish TS
(Turbine System)
Model Numbers:
TS40 - 773-600 (120v)
TS50 - 773-604 (120v)
TS40 - 773-608 (230v)
TS50 - 773-612 (230v)
Pro-Finish TSR
(Turbine System with 2 Quart Remote)
Model Numbers:
TS40R - 773-640 (120v)
TS50R - 773-641 (120v)
TS40R - 773-642 (230v)
TS50R - 773-643 (230v)
Printed in the U. S. A.
P P R R O O
FINISH
(Turbine System with 2
Quart Remote)
Owner's Manual
/ TSP
(Turbine System with
Pressure Pot and Compressor
Pro-Finish TSP
(Turbine System with Pressure Pot
and Compressor on a Cart)
Model Numbers:
TS40P - 773-644 (120v)
TS50P - 773-645 (120v)
TS40P - 773-751-CE (230v)
TS50P - 773-752-CE (230v)
Pro-Finish TSP, Cart Only
Model Numbers:
TSP - 773-618 (120v)
TSP - 773-750-CE (230v)
NOTE: This manual contains important warnings
and instructions. Please read and retain for
reference.
0401 © 2001 Titan Tool Inc. All rights reserved. Form No. 313-1411, REV B
For professional use only
on a cart)
Advertisement
Summary of Contents for Titan PROFINISH TS Series
- Page 1 TS40R - 773-642 (230v) NOTE: This manual contains important warnings TS50R - 773-643 (230v) and instructions. Please read and retain for reference. Printed in the U. S. A. 0401 © 2001 Titan Tool Inc. All rights reserved. Form No. 313-1411, REV B...
-
Page 2: Table Of Contents
10’ (3m) Fluid Hose - 770-465 20’ (6m) Fluid Hose - 770-466 Fluid Hose Coupling - 490-014 Pot Liner Two Gun Adapter 3/8" (9mm) NPS(M) x 3/8" (9mm) NPS(M) Part No. 770-474 Part No. 770-535 © Titan Tool Inc. All rights reserved. -
Page 3: General Repairs/Service
2. When disconnecting wires, use needle nose pliers TITAN Sprayer, call the TITAN: to separate mating connectors. Customer Service Department 1-800-526-5362. Fax 1-800-528-4826 Outside the U.S. Call 1-201-405-7520 Outside the U.S. Fax 1-201-405-7449 Canada 1-800-565-8665 Fax 1-905-856-8496 © Titan Tool Inc. All rights reserved. - Page 4 Clean Air Filter Daily It is extremely important to clean the air filters daily. Air Filters Replaced © Titan Tool Inc. All rights reserved.
-
Page 5: Warnings
(pumps, heaters, filters, valves, spray guns, tanks, etc.). The explosion could cause serious injury, death and/or substantial property damage. Cleaning agents, coatings, paints, etc. may contain Halogenated Hydrocarbon solvents. Titan Tool Inc. spray equipment includes aluminum or galvanized components and will be affected by Halogenated Hydrocarbon solvents. DO NOT USE HALOGENATED HYDROCARBONS IN TITAN EQUIPMENT. -
Page 6: Start-Up Procedures
USER'S MAINTENANCE solvent and unused coatings in an environmentally safe fashion. INSTRUCTIONS Consult with material manufacturer on proper During storage the power cord procedure. must be coiled around cord holder to avoid damage. © Titan Tool Inc. All rights reserved. -
Page 7: Application Techniques
Conversely, if there is an insufficient amount of paint on the surface or you desire to spray faster, a larger orifice tip should be selected. © Titan Tool Inc. All rights reserved. - Page 8 ........© Titan Tool Inc. All rights reserved.
- Page 9 770-043 Screw Inlcudes gaskets and terminals 770-690 Gasket 773-622 TS40 110/120 v 773-731 EMI Filter 773-626 TS40 220/240v 773-712 Stop Washer 773-623 TS50 110/120v 773-706 Foam Strip 773-627 TS50 220/240v 773-724 Wire Mesh © Titan Tool Inc. All rights reserved.
- Page 10 Strain Relief Power Cord 770-503 110/120v 770-309 220/240v 773-660 Air Hose 770-720 Screw 570-008 Fitting 770-777 Manifold 770-775 Connecting tube 773-703 Two quart cup complete 773-665 Rear cover 770-774 Mounting Lug 770-722 Screw © Titan Tool Inc. All rights reserved.
- Page 11 18 inches (46cm) before arcing. You are now ready to turn on the turbine and prepare to spray. For Clean up Procedures see page 7. © Titan Tool Inc. All rights reserved.
-
Page 12: Turbine Mounting Procedure
745-051 Washer 745-016 Screw Pro-Finish Compressor Assembly (770-208 110V 773-736 220V) ITEM No PART No DESCRIPTION 770-097 Bushing 770-205 Compressor, 110V 773-734 Compressor, 220V 770-545 Filter 770-547 Elbow 770-546 Valve 770-204 Air Hose © Titan Tool Inc. All rights reserved. - Page 13 773-033 Trigger 313-1078 Label - Fan Adjustment 773-031 Stem Gland 773-153 Needle, Nozzle Set 773-023 Air Supply Tube 770-178 Fitting 773-167 Handle 773-134 HVLP TOOL* 773-135 BRUSH* 773-162 Fitting *Supplied but not pictured © Titan Tool Inc. All rights reserved.
- Page 14 770-541 Bushing 770-542 Fitting 710-069 Plug 770-540 Regulator 770-544 Guage 770-543 Fitting 770-567 Regulator Complete 770-466 Fluid Hose 770-565 Pot Complete 770-533 Pot Complete (w/o Regulator) 1 770-537 Strainer Show here completely assembled © Titan Tool Inc. All rights reserved.
- Page 15 Cup Assembly Lock Bracket (#82). DO NOT attach hose here. Attach hose (#93) only to Fitting (#92) that is located in Cup Lid (#85) and to Fitting (#12) located on Gun Body (#14). © Titan Tool Inc. All rights reserved.
- Page 16 TITAN WARRANTY FOR THE PRO-FINISH TS / TSR / TSP Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the THERE IS NO OTHER EXPRESS WARRANTY. TITAN HEREBY DISCLAIMS ANY AND original purchaser for use (“End User”), the equipment covered by this ALL IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THOSE OF warranty is free from defects in material and workmanship.