Table of Contents
Advertisement
Quick Links
INSTALLATION & OPERATION MANUAL
CHEESE MELTER
Model: KF-CMG-36
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND
MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
Please call the Service Department and ask for contact information for your local service company.
1
Advertisement
Table of Contents
Summary of Contents for KFE KF-CMG-36
- Page 1 INSTALLATION & OPERATION MANUAL CHEESE MELTER Model: KF-CMG-36 WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT. Please call the Service Department and ask for contact information for your local service company.
-
Page 2: Important For Your Safety
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. -
Page 3: Installation
INSTALLATION, OPERATION AND CARE OF CHEESE MELTER GENERAL Cheese melter are produced with quality workmanship and materials. Proper installation, usage, and maintenance of your Cheese melter will result in many years of satisfactory performance. It is suggested that you thoroughly read this entire manual and carefully follow al l of the instructions provided. -
Page 4: Installation Codes And Standards
The installation location must allow adequate clearances for servicing and proper operation. A minimum front clearance of 24" is required. Do not obstruct the flow of combustion and ventilation air. Adequate clearance for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of air in the room to replace air taken out by the ventilating system. - Page 5 The gas supply line must be ¾” or larger. If flexible or semi-rigid connections are used, the inside diameter must be the equivalent of ¾” iron pip e or larger. All connections of the flexible and semi-rigid type must comply with all local and national requirements.
- Page 6 The minimum supply pressure (upstream of the regulator) should be 7-9” W .C. for natural gas and 11 -12” W .C. for propane gas. At no time should the regulator be connected to supply pressure greater than ½ psi (3.5 k Pa) or 14”...
- Page 7 MOUNTING OVER GAS RANGE BACK DESIGNED TO MOUNT THIS CHEESE MELTER CHEESE MELTER (Fig. 6) If the Cheese melter is to be mounted over a gas range WHICH IS DESIGNED SPECIFICALLY TO RECEIVE THIS KFECHEESE MELTER, it must be installed according to the instructions below: Using the twelve bolts provided (balloon 1), install mounting brackets (balloon 2) on both top mounting posts (balloon 3).
- Page 8 Cheese melter - Range back installation 1. Take off the 12 self-tapping screws on the range back. 2. Insert the Cheese melter support column into the Range back plate as shown and tighten it with screws...
- Page 9 3. Lift Cheese melter and attach it to the proper position of the support column...
- Page 10 4. Take two brackets out of the package...
- Page 11 5. Attach Cheese melter mounting track to the appropriate screw according to the hole position and tighten all screws...
-
Page 13: Operation
OPERATION WARNING: THE CHEESE MELTER AND ITS PARTS ARE HOT. BE CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE CHEESE MELTER. CONTROLS Angled Handle —Elevates or lowers the broiling drawer and grate to different positions. Grasp the handle and pull towards Cheese melter cavity. This releases the mechanism and allows the lifting handle to move into the desired position. Burner Valve —... - Page 14 [键入文字]...
- Page 15 When service is needed, contact a KFE Authorized Service Agency, or your dealer. To avoid confusion, always refer to the model number, serial number, and type of your unit.
-
Page 16: Warranty Information Form
LIMITED ORIGINAL COMMERCIAL EQUIPMENT WARRANTY FOR WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose. Date of purchase :____________________________________ Model No. : ____________________________________ Serial No. : ____________________________________ Your notes: [键入文字]...