Advertisement
Quick Links
4 + 2 Drawer Chest
Assembly Instructions
002 xx 6642
- Please keep for future reference
Dimensions
Width - 66.8cm
Depth - 35.2cm
Height - 88.4cm
MADE IN
GREAT BRITAIN
Important -
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev C - 20/06/2016
Advertisement
Summary of Contents for JD Williams and Co ASPEN 4+2 DRAWER CHEST
- Page 1 4 + 2 Drawer Chest Assembly Instructions 002 xx 6642 - Please keep for future reference Dimensions Width - 66.8cm Depth - 35.2cm Height - 88.4cm MADE IN GREAT BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline.
- Page 2 Safety and Care Advice Important - Please read these instructions fully before starting assembly Do not stand or put weight on Check you have all the We do not the product, this could cause components and tools listed on recommend the damage.
- Page 3 Components - Panels Please check you have all the panels listed below Important - Thick lines indicate finished edges 0323 Divider Panel (32.8x16.0cm) 4968 (66.8x35.2cm) 0315 5377 End Panel x 2 (80.4x32.8cm) Bottom Panel (66.8x35.2cm) 8312 Backpanel (83.0x66.0cm) 624xx7010 4881 Drawer back x4 Draw Front (Top Left) 5671...
- Page 4 If you have damaged or missing components, call the Components - Fittings Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline. Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly, In some case more fittings may be supplied than are required.
-
Page 5: Exploded View
Exploded View 4968 0315 8312 0323 0315 5377 624xx7003 622xx7002 4883 4881 622xx7002 624xx7003 623xx7002 622xx7002 624xx7010 4883 4882 623xx7002 5671 4717 Large Drawers x4 623xx7002... - Page 6 Assembly Instructions Step 1 Fitting dowels to top panel. Insert 6 metal dowels into the top panel 4968 4968 Note: Tighten metal dowels up fully against the panel. Do not over-tighten. Step 2 Fitting cams and dowels to the end Important :- panels.
- Page 7 Assembly Instructions Important :- Step 3 Attaching runners to Lay end panels end panels out as shown Important :- Lay end panels out as shown Position the runner so that the front hole of the runner lines up with the pre-drilled hole 0315 nearest to the edge of the panel.
- Page 8 Assembly Instructions Step 4 Fitting cams and runners to the divider. Insert the runner 2 cams into the right face if the divider panel 0323 0323 Turn the panel over and insert runner Take care not to damage the floor when turning panel with exposed fittings over.
- Page 9 Assembly Instructions Left hand side Insert wooden dowels 622xx7002 in drawer back Drawer Back 624xx7010 into holes in 624xx7010 left 622xx7002 right hand 623xx7002 drawer sides. Right hand side 623xx7002 Sit drawer bottom 5671 into groove on drawer front 4717 Foil surface facing upwards.
- Page 10 Assembly Instructions Step 7 Fitting dowels to the drawer front. Insert 2 metal dowels into the the drawer 4881 front Repeat on the drawer 4881 front 4882 4882 Step 8 Insert small cams Right hand side 622xx7002 into left 623xx7002 and right 623xx7002 drawer sides.
- Page 11 Assembly Instructions Sit drawer bottom 4883 into groove on drawer front 4881 Ensure foil on the drawer bottom is facing upwards. Foil surface facing upwards. Plain chipboard surface 4883 to underside. 4881 : Locate the metal dowels (already inserted) in the drawer front into the small cams in the left and right hand drawer sides.
- Page 12 Assembly Instructions Step 10 0323 Connect the top panel to the divider panel. Connect the dowels in the 4968 top panel to the cams in the divider panel 4968 0323 Turn cams 180 degrees to lock. Step 11 Panels sit flush Connect the end panels 0315 to the top panel.
- Page 13 Assembly Instructions Step 13 Squaring up the unit. DIAG 2 DIAG 1 DIAG 3 IMPORTANT! Ensure a tape measure is used to square unit up. Before securing the back it is necessary to square up the unit. You can do this by measuring between XX - XX and YY - YY ensuring these are the...
- Page 14 Assembly Instructions Step 15 Attach the feet to the bottom panel. Use a bradawl to mark out the holes for the feet. Use 4 screws to attach feet to the bottom panel 5377 Stand the unit upright once you have finished this step.
- Page 15 Assembly Instructions Step 16 Fixing to wall We recommend that this unit is fixed to a suitable wall to prevent possible overbalancing. We have included a fixing bracket for this. No fixing screws are provided as they will need to suit the wall type, and the length of screw will depend on the distance from the...
- Page 16 Assembly Instructions Step 17 Fit the drawers. For this step we recommend you follow the helpful hints on the 2nd Hole next page. 4881 4882 4717...
- Page 17 Assembly Instructions Step 18 Locate drawers helpful hints Pull sliding part of drawer runners so they are fully extended. Locate drawer onto runners. Locate screwdriver into second threaded hole in drawer runner Keeping screwdriver in place push the drawer in until the screwdriver pushes against the 2nd Hole panel.
- Page 18 Assembly Instructions Congratulations! Your unit is complete. Important Information If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 8am - 4.30pm (Monday to Thursday) 8am - 2.30pm (Fridays) (by contacting the customer service line your statutory rights are not affected) Please have the following information to hand: >>...