Advertisement
2. introduCtion
Heavy-duty high level stand to safely support vehicles when wheel free operations are being carried out. supplied with three interchangeable
crutches for even load support. Heavy gauge steel frame and welded construction give superior strength and safety. features captive, spring
assisted, multi-position pin load support and retracting castors for easy manoeuvrability. Ideal for commercial vehicles. sold as singles.
Independently UK load tested.
3. speCifiCation
model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .asC50 . . . . . . . . . . . . . . . . . asC70 . . . . . . . . . . . . . . . . . . . . . asC120
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5tonne. . . . . . . . . . . . . . . . . . 7tonne . . . . . . . . . . . . . . . . . . . . . 12tonne
minimum Height:. . . . . . . . . . . . . . . . . . . . . . . . .1295mm . . . . . . . . . . . . . . . . 1295mm. . . . . . . . . . . . . . . . . . . .1295mm
maximum Height: . . . . . . . . . . . . . . . . . . . . . . . .1905mm . . . . . . . . . . . . . . . . 1905mm. . . . . . . . . . . . . . . . . . . .1905mm
4. Contents
Item 2
b
a
5. assembly
Assembly will require two persons. The central column will be partially assembled with a tube fully inserted against the forces of an internal
compression spring.
▲
it is important to leave this tube inserted and pinned as supplied at this stage.
5.1.
offer the three tripod legs (item 3) into the central column pockets (item 1).
5.2.
Fit loosely the three cross members (item 5) to the tripod legs with fixings (items 7,9,10,11)
5.3.
Fit loosely the three brackets (item 6) to the tripod legs with fixings (items 8,9,10,11) and the central column ring with fixings (items
7,9,10,11).
5.4.
Tighten all fixings to form a rigid geometrically aligned frame.
6. operation
6.1.
Before undertaking work conduct a risk assessment with a responsible person and ensure it covers the weight to be supported and
a margin for error. never work alone on a vehicle supported on these stands. It is the employer's responsibility to ensure the operator
has read these instructions and is familiar with the products use and limitations. ensure that all operators can read english or have the
instructions explained to them in their native language. Also ensure the warnings on the product are observed.
6.2.
Use only in conjunction with a vehicle lift - never with any other jacking device. elevate the lift to the appropriate height and locate the
supports, with the appropriate saddles onlY on the Vehicle manufacturers recommended jacking/support positions.
6.3.
for large movement of the column tube it will be necessary to retain it by hand whilst withdrawing the height setting pin. Allow
the column tube to elevate assisted by the spring to the nearest available pin hole prior to engaging with the vehicle. ensure the pin
is inserted fully and safety pinned, then rotate the fine adjuster to close the gap to zero at all locations. always insert the pin through
the hole in the collar of the stand and the support column.
6.4.
Use a maximum of 2 stands per axle only and in multiples of 2 evenly across the rest of the load if required. Be CeRTAIn that all
the stands are set to a height that will leave the vehicle supported completely horizontal and not at an angle that could cause
slipping on the stand support heads. Check this on the vehicle across its length And its width. ensure there are no objects or
individuals in the area other than the operator and the supervisor and no person or article is under the vehicle. Take extreme
care to lower the lift slowly and reduce its height only the minimum distance you need to achieve the wheel free status required.
engage the assistance of a colleague while you perform this task. loWeR onTo All sTAnds BeInG Used AT THe sAme TIme.
WarninG! When Vehicle is supported on stands never apply excessive force to fastenings or run the engine.
‰
© Jack sealey limited
Item
c
1
2a,b,c
3
4
5
6
7
8
9
10
11
Original Language Version
description
Central Column sub Assembly
saddles
Tripod leg
swivel Castor sub Assembly
Cross members
Bracket
Hexagon screw m12 X 40
Hexagon Bolt m12 X 90
Hexagon nut m12
Plain Washer Ø12
spring Washer Ø12
AsC50, AsC70, AsC120 Issue 2 (f) 21/11/18
Qty
1-set
1-set
3
3
3
3
9
3
12
24
12
Advertisement
