ICS 701-A Operator's Manual
  1. Manuals
  2. Brands
  3. ICS Manuals
  4. Cutter
  5. 701A
  6. Operator's manual

ICS 701-A Operator's Manual

Hide thumbs Also See for 701-A:
Table of Contents

Advertisement

Quick Links

Download this manual
Model # 701-A
OPERATOR'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 701-A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ICS 701-A

Summary of Contents for ICS 701-A

  • Page 1 Model # 701-A OPERATOR’S MANUAL...

  • Page 2: Table Of Contents

    TECHNICAL SPECIFICATIONS SET-UP 8 - 13 OPERATION 14 - 19 TROUBLESHOOTING MAINTENANCE 21 - 23 REFERENCE SPARE PARTS LIST 26 - 29 DECLARATION OF CONFORMITY © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

  • Page 3: Symbols & Labels

    • Do NOT use this saw cover on any other saw model. • Do NOT operate saw without baffle drain. • Failure to observe these precautions can result in serious injury. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...

  • Page 4: Safety

    Using wood cutting saw chain on the ICS saw could result in severe injuries to operator and bystanders! Use ONLY the cutting attachments specifi ed in this manual on this saw. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 5 If you experience tingling, numbness, pain or changes in skin color, particularly in your fi ngers, hands or wrists, stop using the saw immediately. If the problem persists, seek medical attention. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 6 • Breathing exhaust fumes is dangerous. Provide ventilation in closed areas. • To avoid electrocution, check for live electrical wiring near cutting area. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...

  • Page 7: Technical Specifications

    “service unit with pressure regulator” in the line to prevent over speeding the saw. •Always use an in-line oiler(ICS p/n 575013 or 575130) or air pac ICS p/n 575013 to provide continuous lubrication to the air motor. This will increase the life of the saw and reduce down time.

  • Page 8: Set-Up

    Loosen the side cover nuts and remove the side cover and bar clamp plate. STEP 2 Place the bar onto the studs and the chain adjustment pin. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 9 STEP 4 Mount the chain on the bar starting at the drive sprocket & continue over the bar nose. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 10 STEP 6 Install the bar clamp plate over the bar studs in proper orientation. "Front" is marked on the plate. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 11 Finger tighten only. STEP 8 Tension the chain properly. Do not over tension the diamond chain. Loss of power will result. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 12 1/2 in (12 mm) to 3/4 in (18 mm) below the bar, it is time to tension the chain. CHAIN TOO TIGHT CHAIN TOO © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 13 Lift up on the nose of the bar and firmly tighten the side cover nuts. Be sure the side cover nuts are tightened to approximately 20 ft-lbs (27 Nm). © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...

  • Page 14: Operation

    WallWalker can also be very sharp. WARNING WARNING Before tensioning chain, always turn the compressor off and relieve system pressure before disconnecting from the compressor. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 15 SAE 10 W oil. In winter or when using very moist air, use antifreeze lubricant, such as “ICS Prolube ATL/AF”, “Killfrost” “BP Energol AX10” or “Kompranol” © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 16 • Avoid pinching the bar and chain. Always cut the bottom of an opening fi rst, then top, and then the sides. Save the easiest cut for last. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 17 When using a new chain, cutting speed can be increased by “opening up the diamonds”. Make a few plunge cuts in an abrasive material such as a cinder block. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 18 Wallwalker into the cut and push straight in. The Wallwalker will force the saw to feed down. © 2016 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...
  • Page 19 5. When done cleaning saw, spray entire saw body, chain, bar, and drive sprocket with a lightweight penetrating oil. This will minimize rust and reduce slurry build up on saw assembly. © 2015 ICS, Blount International Inc. Specifi cations are subject to change without notice. REV02292016 F/N 573498...

  • Page 20: Troubleshooting

    Vanes sticky. Apply lubricant directly to saw air inlet and blow motor clear. Repeat if necessary. See maintenance instructions Further questions? Call 800.321.1240 or visit our website at: icsdiamondtools.com © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

  • Page 21: Maintenance

    MAINTENANCE 701-A SERIES OPERATOR’S MANUAL THIS PAGE INTENTIONALLY LEFT BLANK © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 22 • Install sprocket in reverse order ensuring counter bore is facing out. • Install snap ring STEP 2 • Ensure snap ring is fully seated in snap ring groove. © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 23 7. Air lubricator (oiler) can be adjusted to maximize atomization and minimize excessive oil use. KEEP TOOL CLEAN - See system clean up on page 9. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

  • Page 24: Reference

    2. Determine the length of the cut in feet. 3+7+3+7=20 feet 3. Multiply the two numbers 8 in x 20 ft = 160 in-ft © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 25 701-A SERIES OPERATOR’S MANUAL THIS PAGE INTENTIONALLY LEFT BLANK © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

  • Page 26: Spare Parts List

    SPARE PARTS LIST 701-A SERIES OPERATOR’S MANUAL © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 27 565065 Drive Sprocket (includes snap ring) 70639 Retaining Nut Kit (set of 2) 528564 Side Cover Replacement Kit 576613 NPT Fitting 3/4 x 14” © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 28 SPARE PARTS LIST 701-A SERIES OPERATOR’S MANUAL © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 29 ScrewM6 x 16 SHCS plated 71133 Screw Hose Clamp 71065 90 degree water fitting 71896 WallWalker® Stud C-Clip 70873 Lever Arm 70874 Pro Pivot Stud © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 30 701-A SERIES OPERATOR’S MANUAL THIS PAGE INTENTIONALLY LEFT BLANK © 2016 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

  • Page 31: Declaration Of Conformity

    701-A SERIES OPERATOR’S MANUAL © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...
  • Page 32 701-A SERIES OPERATOR’S MANUAL ICS, BLOUNT INC. 4909 SE INTERNATIONAL WAY PORTLAND, OR 97222 800.321.1240 icsdiamondtools.com © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV02292016 F/N 573498...

Table of Contents