Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for APE Multi-Gauge
-
Page 2: Table Of Contents
Table of Contents Introduction ....................Getting Started ..................... Vehicle Health ..................What’s Included ..................Installation ....................Flex Sensor Installation ................Wire Harness Installation ................. Gauge 1 &2 Installation ................iOS/Android phone application ..............App Dashboard Screen ................App Data-Logging Screen ............... App Fuel Calculator Screen .............. -
Page 3: Introduction
Bluetooth Low Energy on our Android or iOS application. The Multi-Gauge also provides a raw ethanol sensor output with built in 10K pullup resistor to 5V so you can use it on a vehicle that already has a flex... -
Page 4: Getting Started
E85 usage. From then on, the changes should be made at manufacturers recommended intervals. What’s Included Check to make sure you have all of the necessary components in your kit: • Multi-Gauge Module • Flex Fuel Sensor • Wiring Harness • Quick Connect Fuel Fittings and hose clamps •... -
Page 5: Installation
1) Install Flex Fuel Sensor anywhere in the fuel lines. A good place is at the fuel filter. Make sure the Flex Fuel Sensor connector on the Multi-Gauge wiring harness is able to reach the sensor. 2) You can use the supplied fuel line adapters to connect the Flex Fuel sensor to the fuel filter. -
Page 6: Wire Harness Installation
7) The purple wire outputs the raw signal from the Flex Fuel Sensor. The Multi-Gauge Module has a built in 10K pullup to 5V on this signal. This can be used to connect to your ECU if... -
Page 7: Gauge 1 &2 Installation
5V on the module. This can be connected directly to an ECU 11) Plug the Multi-Gauge Module into the harness and mount in your car. 12) Now it is time to start up the APE app on your phone. -
Page 8: Ios/Android Phone Application
You can install the APE X85 from either the Apple App Store or the Google Play Store. Open the app and connect to your device, you should see your serial number listed as something like “APE-MG-10001”. -
Page 9: App Dashboard Screen
App Dashboard Screen Current value read Current value read by Gauge 1 input. by Gauge 2 input. It is 0.0 to 5.0 by It is 0.0 to 5.0 by default, the scaling default, the scaling information needs information needs to be entered in to be entered in the settings tab. - Page 10 App Dashboard Screen Selecting either Gauge 1 or 2 in the top corners will swap that gauge into the center and put the Ethanol Content in the corner. If you set the warning range in the settings tab and your gauge hits that range, the gauge will turn red.
- Page 11 App Dashboard Screen If you are on the dashboard screen and rotate your phone counter- clockwise, then you the gauges will rotate to a landscape view. If you are on the dashboard screen and rotate your phone clockwise, then you will be taken to the data-logging screen.
-
Page 12: App Data-Logging Screen
App Data-Logging Screen Rotating your device to the right will show the data logging screen. You can select any point on the graph, and it will show you the values at that point. You can pause, and zoom in and pan to a section, and hitting save will copy a screenshot to your photos. -
Page 13: App Fuel Calculator Screen
App Fuel Calculator Screen The fuel calculator can show you how to mix Ethanol with Gasoline to achieve a desired Ethanol mixture, for example E65. You can use the datalogging screen to help determine if you need to lower your Ethanol mixture. -
Page 14: App Settings Screen
App Settings Screen Hit the Save button after any Displays Module changes are made Firmware and App Version Changes Gauge Trim from silver Pass Key not to black used for Multi- Gauge Can turn off Gauge 1 Display Display Name is on dashboard if what is shown not used... -
Page 16: Warranty
Returns If you are experiencing an issue with your Multi-Gauge module, please contact us so we can help resolve it. If you wish to return the system, all components must be returned in original packaging, in resalable condition.
Need help?
Do you have a question about the Multi-Gauge and is the answer not in the manual?
Questions and answers