Advertisement
Quick Links
Advertisement
Summary of Contents for Cedia FLATLIFT SUPERFLAT
- Page 1 Operating Manual P.01 O u t p e r f o r m . O u t l a s t .
-
Page 2: Table Of Contents
Operating Manual CONTENTS P.02 CONTENTS O u t p e r f o r m . O u t l a s t . K.01 INTRODUCTION K.02 FEATURES K.03 PRODUCT DIMENSIONS K.04 INITIAL PRODUCT SET-UP Set-up P.06 Images P.07 - P.08 K.05 PRODUCT CONTROL Programming the remote control (S435) -
Page 3: Introduction
Operating Manual INTRODUCTION P.03 C.01: INTRODUCTION O u t p e r f o r m . O u t l a s t . Intended Use The product swivels out of LCD and plasma TV equipment. All company names and product names are trademarks of the corresponding owner. All rights reserved. The scope of supply can vary depending on the product and the range of fixtures and fittings. -
Page 4: Features
TV size 52-65“ (inch) Scope of supply: opening rate 18%/h Soft Start / Soft Stop Low noise level < 45 db Flatlift Superflat Environmental temperature from +5°C bis 40°C Control box 230V power supply unit Motor cabel (1x) 433,92 MHz receiver... -
Page 5: Product Dimensions
Operating Manual PRODUCT DIMENSIONS C.03: P.05 PRODUCT DIMENSIONS O u t p e r f o r m . O u t l a s t . 1500 1540... - Page 6 O u t p e r f o r m . O u t l a s t . Initial setting /installation: 1) Fix your Flatlift Superflat (img.1, no.1 and P.07, img. 1b) with 2 screws upon the wall. Depending on assembly you can swivel your Superflat system left- or rightwards 2) Connect the motor (img.1, no.
-
Page 7: Initial Product Set-Up
Operating Manual INITAL PRODUKT SET-UP C.04: P.07 INITIAL PRODUCT SET-UP O u t p e r f o r m . O u t l a s t . Image 1b Image 1c Image 1d... - Page 8 Operating Manual INITIALPRODUCT SET-U C.04: P.08 INITIAL PRODUCT SET-UP O u t p e r f o r m . O u t l a s t . Image 2 Image 3 Image 5 Image 4...
-
Page 9: Product Control
Operating Manual PRODUCT CONTROL C.05: P.09 PRODUCT CONTROL O u t p e r f o r m . O u t l a s t . Programming the remote control (S435): You can also get additional remote controllers for your Flatlift system (optional extra). As the controllers are coded, you have to programme them. - Page 10 Operating Manual PRODUCT CONTROL C.05: P.010 PRODUCT CONTROL O u t p e r f o r m . O u t l a s t . Resetting the receiver: It may sometimes occur that the transmitting codes stored in the receiver are lost. In this case, the receiver must be cleared and re-programmed.
- Page 11 Operating Manual PRODUCT INTEGRATION C.06: P.011 PRODUCT INTEGRATION O u t p e r f o r m . O u t l a s t . Infomation TV swiveling: The Superflat can swivel out up to 90° (img.1) Please consider that the liftsys- tem needs space between the TV and the e.g.
- Page 12 Operating Manual PRODUCT INTEGRATION C.06: P.012 PRODUCT INTEGRATION O u t p e r f o r m . O u t l a s t .
- Page 13 P.013 PRODUCT INTEGRATION O u t p e r f o r m . O u t l a s t . The Flatlift Superflat automatic swivel LCD-/Plasma Wallmounts are special developed motorized mounting con- cepts for LCD and Plasma Flatscreens.
- Page 14 Operating Manual TROUBLE SHOOTING C.08: P.014 TROUBLE SHOOTING O u t p e r f o r m . O u t l a s t . Trouble shooting: If your Flatlift is not working properly, please make sure you check the following things: The Flatlift won’t move up or down Is the power cord attached to the control box? Check the mains connection...
- Page 15 Operating Manual LEGAL NOTICE C.09: P.015 LEGAL NOTICE O u t p e r f o r m . O u t l a s t . FLATLIFT Referencen Legal Notice FLATLIFT TV Lift Systeme GmbH Gewerbegebiet Südwest Niedesheimer Str. 15 67547 Worms, GERMANY Tel.: +49 (0) 62 41 97 20 10 Fax.: +49 (0) 62 41 97 20 12...