Related Manuals for CH Hanson Norse 9682080
Summary of Contents for CH Hanson Norse 9682080
- Page 1 9682080_oipm_EN011_9643316.01 03/30/18 Page 1 Operating Instructions & Parts Manual Model 9682080 8˝ Variable Speed Bench Grinder 9643316.01 0318...
- Page 2 9682080_oipm_EN011_9643316.01 03/30/18 Page 2 NORSE Operating Manual & Parts List 9682080 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! retain instructions for future reference.
- Page 3 9682080_oipm_EN011_9643316.01 03/30/18 Page 3 NORSE Operating Manual & Parts List 9682080 GETTING STARTED M. Eyeshield knob (2) N. Tool rest support, left (1) Structural Requirements O. Tool rest support, right (1) Make sure all supporting structures and load attaching devices are P.
- Page 4 9682080_oipm_EN011_9643316.01 03/30/18 Page 4 NORSE Operating Manual & Parts List 9682080 SAFETY RULES ( CONTINUED ) • DO NOT use electrical tools in the presence of flammable liquids or gasses. • ALWAYS UNPLUG THE TOOL FROM THE ELECTRICAL For your own safety, read all of the instructions and precautions before RECEPTACLE when making adjustments, changing parts or operating tool.
- Page 5 9682080_oipm_EN011_9643316.01 03/30/18 Page 5 NORSE Operating Manual & Parts List 9682080 SAFETY RULES ( CONTINUED ) • REPLACE A CRACKED OR DAMAGED GRINDING WHEEL IMMEDIATELY. A damaged wheel can discharge debris at a • ALWAYS WEAR A DUST MASK TO PREVENT INHALING high velocity towards the operator.
- Page 6 9682080_oipm_EN011_9643316.01 03/30/18 Page 6 NORSE Operating Manual & Parts List 9682080 SPECIFICATIONS 14. 8" WIRE WHEEL - Used to remove rust and dirt from workpiece. Know Your Bench Grinder 15. EYESHIELD - Protective Lexan see-thru shields to prevent any loose debris from contacting the operator. Refer to Figure 2.
- Page 7 9682080_oipm_EN011_9643316.01 03/30/18 Page 7 NORSE Operating Manual & Parts List 9682080 ASSEMBLY 3. Adjust each tool rest until its inside edge (I) is 1/16˝ from the grinding wheel. Firmly tighten the hex head screws holding the The Bench Grinder is provided with a left and right two piece tool supports.
- Page 8 9682080_oipm_EN011_9643316.01 03/30/18 Page 8 NORSE Operating Manual & Parts List 9682080 ASSEMBLY ( CONTINUED ) NOTE: The flexible work light can be turned “ON” or “OFF” even if the Bench Grinder is turned “OFF”. Eyeshields 1. Assemble the eyeshield (C) to the spark arrestor (A) inserting The Flexible Work Light housing will carriage head screw (B) through eyeshield and the spark remain hot for a few minutes after turning...
- Page 9 9682080_oipm_EN011_9643316.01 03/30/18 Page 9 NORSE Operating Manual & Parts List 9682080 INSTALLATION ( CONTINUED ) In all cases, make certain the electrical Grounding Instructions receptacle in question is properly grounded. If you are not sure have a certified electrician Refer to Figures 10 and 11. check the electrical receptacle.
- Page 10 9682080_oipm_EN011_9643316.01 03/30/18 Page 10 NORSE Operating Manual & Parts List 9682080 OPERATION ( CONTINUED ) 5. Move the wheel dresser forward until the serrated wheels (D) make light contact with the grinding wheel (C). After contact 6. Adjust the eyeshields. Place the workpiece on the appropriate has been made, slide the wheel dresser side to side across the tool rest for the desired operation.
- Page 11 9682080_oipm_EN011_9643316.01 03/30/18 Page 11 NORSE Operating Manual & Parts List 9682080 OPERATION ( CONTINUED ) 8. Replace the abrasive wheel, outer wheel flange and arbor hex nut. NOTE: The arbor hex nut on the left arbor shaft is left hand threaded and is tightened by rotating it counter-clockwise.
- Page 12 9682080_oipm_EN011_9643316.01 03/30/18 Page 12 NORSE Operating Manual & Parts List 9682080 TROUBLESHOOTING GUIDE TO PREVENT INJURY TO YOURSELF or damage to the Bench Grinder, turn the switch to the “OFF” position and unplug the power cord from the electrical receptacle before making any adjustments. Symptom Possible Cause(s) Corrective Action...
- Page 13 9682080_oipm_EN011_9643316.01 03/30/18 Page 13 NORSE Operating Manual & Parts List 9682080 NOTES...
- Page 14 9682080_oipm_EN011_9643316.01 03/30/18 Page 14 REPAIR PARTS LIST FOR 9682080 8˝ VARIABLE SPEED BENCH GRINDER NORSE Operating Manual & Parts List 9682080 31 32...
- Page 15 9682080_oipm_EN011_9643316.01 03/30/18 Page 15 REPAIR PARTS LIST FOR 9682080 8˝ VARIABLE SPEED BENCH GRINDER NORSE Operating Manual & Parts List 9682080 PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. 4-0.7 x 6mm Pan Head Screw* 9636165.00 Flange 4mm Flat Washer* 9602033.00 Grinding Wheel 60# 9636145.00...
- Page 16 9682080_oipm_EN011_9643316.01 03/30/18 Page 16 NORSE Operating Manual & Parts List 9682080 NORSE Warranty NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended.