Advertisement
Quick Links
7" In-Wall Touch Screen-
Adapter Kit for Mini
Touch Screen
Installation Guide
Supported Touch Screen Models
• C4-TSWMC7 – 7" In-Wall Touch Screen, Black or
White
Supported Adapter Kit Models
• C4-7IETOMTSAK, Black or White
General Description
This Control4® adapter kit provides an adapter plate
to accommodate the installation of a 7" In-Wall Touch
Screen. The kit is intended for an existing Mini Touch
Screen to be replaced by a 7" In-Wall Touch Screen.
Requirements
• Tools to modify the back box, such as a tape
measure, a pencil, a screwdriver, a small saw to
cut heavy plastic, a utility knife, or a handheld
rotary cutting tool.
• A 5/16" nut driver or socket wrench, if using the
metal wall box.
What's in the Kit
• Adapter plate
• Two (2) screws for power box installation
• 7" In-Wall Touch Screen Adapter Kit for Mini
Touch Screen Installation Guide (this document)
Specifications
Adapter Kit for a Plastic Back Box Model:
• Plastic back box (installed previously)
• Adapter plate
™
Adapter Kit for a Metal Back Box Model:
• Metal back box (installed previously)
• Adapter plate
Prepare for Installation
Plastic Back Box Model
1
Remove the old Mini Touch Screen and leave the
back box in place in the wall.
2
Note the angle-shaped back box divider inside
the box (see below). You'll need to cut a section
out of this back box divider. Using a heavy knife
or a handheld rotary cutting tool, measure and
mark 1 inch down from the front of the divider.
3
Cut vertically down so there's a 1-inch cutout in
the back box divider. You'll need this space for
the 7" In-Wall Touch Screen power box.
4
Remove the plastic piece you just cut out (see
photo next).
Back Box Divider Cutout
5
Go to the 'Installation' section next for more
instructions.
Metal Back Box Model:
1
Remove the old Mini Touch Screen and leave
the back box in place in the wall (see example
below).
Back Box
Divider
2
Using a screwdriver, remove the screw that holds
the back box divider in place.
3
Remove the back box divider. You'll need this
space to install the 7" In-Wall Touch Screen
power box. While you're at it, also remove the
grounding screw from the back box. You'll need
this screw to move the grounding wire to your
new adapter plate.
Advertisement
Summary of Contents for Control 4 C4-7IETOMTSAK
- Page 1 Supported Touch Screen Models or a handheld rotary cutting tool, measure and mark 1 inch down from the front of the divider. Cut vertically down so there’s a 1-inch cutout in • C4-TSWMC7 – 7” In-Wall Touch Screen, Black or the back box divider. You’ll need this space for White the 7” In-Wall Touch Screen power box. Supported Adapter Kit Models Remove the plastic piece you just cut out (see photo next). • C4-7IETOMTSAK, Black or White Back Box Divider Cutout General Description This Control4® adapter kit provides an adapter plate to accommodate the installation of a 7” In-Wall Touch Screen. The kit is intended for an existing Mini Touch Screen to be replaced by a 7” In-Wall Touch Screen. Requirements Go to the ‘Installation’ section next for more instructions. • Tools to modify the back box, such as a tape measure, a pencil, a screwdriver, a small saw to Metal Back Box Model:...
- Page 2 in the kit to attach the power box to the adapter ™ plate. Insert the 7” In-Wall Touch Screen’s power box into the adapter plate’s hole and screw it in place (see the next photo). 7” In-Wall Touch Screen- Adapter Kit for Mini Touch Screen Installation Guide Note: Attach the ground wire to the wall box in the location indicated by the Ground symbol. Attach the new 7” In-Wall Touch Screen. Go to the ‘Installation’ section next for more instructions. Warranty Installation Limited 2-year Warranty. Go to http://www.control4. com/warranty for details. Insert the grounding screw into the back of the adapter plate (metal model). Secure the About This Document grounding wire to the grounding screw. Part number: 200-00200, Rev. F 7/06/2011 Place the metal adapter plate on top of the back box, and screw it onto the back box using the two (2) screws that were used to hold the old Touch Screen in place. Insert the screws in the opposite corners of the plate (see photo below). Screw hole Screw hole Adapter plate Insert Power Box here Follow the installation instructions in the 5” and 7” In-Wall Touch Screen Installation Guide to attach the high or low-voltage connections to the...
- Page 3 ™ control4.com | ©2011 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.