Subscribe to Our Youtube Channel
Summary of Contents for Daihatsu EDM18ZII
- Page 1 INSTRUCTION 11ANUAL DAlHA TSU .Ml CROPROCESSOR-CO NTROLLED DOOR OPERATOR MODEL: EDM18ZII EDM30ZII DAIHATSU DIESEL MFG. CO., LTD.
- Page 2 Daihatsu slide control Start up settings Alarm switch Close speed Cushion Open speed TSTR Braking 2X Dip/Sw Torque Open timer 8 X Dip/Sw: DOWN DOWN DOWN DOWN UP unless electric lock fitted, then DOWN DOWN DOWN These settings must be performed before initial power up.
- Page 3 1. Features High performance • The DC motor remains cold during continuous door operation. • Quick opening and closing. Maximum speed is 500 mm per second . • The brushless moulded motor and the completely enclosed reduction gear are silent, durable, and maintenance-free.
- Page 4 • Optical safety system A safety beam switch which operates as long as the door is open, can be used with this door operator. detection and automatic reset • Overload If the door stays overloaded for 15 seconds or longer, the power to the motor is shut off and an alarm sounds.
-
Page 5: External Switches
DM18ZJ30Z) MICOM DOOR 'Ich (551 Jiwit n .wilc;h( os. (.1., =b~", 'l« 0 Ib~n 'Y Colas and'e External switches Half-open selector switch Installed for double-sliding or long-stroke doors. Turning this switch ON allows half-open door operation. Panic switch (PS) Upon receipt of a signal from an emergency sensor... - Page 6 4. Doorhanging hrackets The door hanging brackets are made of iron and are connected to the door with bolts. Each pulley has a greased, sealed ball bearing and a plastic tire. The rail is extruded aluminum. For installation on fire doors, the pulley tires and rail are made of iron (EDM-30Z) 5.
- Page 7 Dmer Open llom &onal s.eflsor lamp) IWlld> (10050( low. low. Br king .peed High'lpeed Br. ing 'peed CUlhion"," • c..stooning Door _----- Door ~ame h"", .•. Pros •. opened •••• ed CUIhionong ",eke 50 • 70 nvn Cuohaontog siroN> 50 • 70 mm --t-j-- 0001 &lloko 000J .troll.u...
- Page 8 The above problems are just temporary. Remove the obstacle or repair. The door resumes normal operation automatically after about 15 seconds or after the sensor switch is turned ON then OFF. Short ton. long tonQ <i>-'.-'- Timor " rm OWOfF P""""...
- Page 9 _S'll Conventional electrically-driven door operators detect the door stroke or braking position with position sensor switches. The Daihatsu Microprocessor-controlled Door Operator counts the number of pulses from the motor, and memorizes as the door stroke. Based on this, the operator adjusts the braking position and half-open position.
- Page 10 Opening: As soon as the sensor switch triggers an ON signal, the door starts to open at high speed. It then slows to low speed until it reaches the full open it is held in position. position, where Closing: After the sensor switch triggers...
-
Page 11: Door Sliding
Spanner 5. Adjustments 1. Drive belt tensl becomes slack drive belt "t can fou tlon 1 'ng opera the drlv durl Keep other compo the lock nu loosen t" belt tlgh (see and tighten the clamp right) V boll tment (for both '"... - Page 12 • , • I•.••. ; ••• 0'1_ --I~o • • •_w LaoI" •••• ' - NO-.., 1."'''"'''1 •••• " •• , •• "'. I.ec"""t , ••• _ . ,.70'110 •• I••••• ,•••••••• " •••• 101' DAIHATSU DIESEL MFG.CO ••LTD. .,tAli,,,.
- Page 13 2. Setting up before Initial stroke determining sequence Set the following before turning on the 100V AC 1t.1I O' l,eclloo T.STR " Op~n power source. MI@!)~ 1) Door direction selector C++A .•.• Shift this selector depending on the L R.D. door direction.
- Page 14 "Fixed"/"Auto" cushioning Factory-set to Auto (lower position). For a swing door, set this switch to F,xed (upper positIOn) 8-6 Press-closing: OFF when an abnormality is detected/constantly Factory-set to ON (lower position) 5-7: Battery open/close selector 5.1.2.3.4.5.6.7.8 ~~ 00",,,,,, HO.l'J'I.S! ::t@MMMI~~ The door opens when power is cut off.
- Page 15 lights the sensor Pressing the test button indicator (red) Brake force adj ustrnent Adjust the brake force so that the low-speed zone is set to 50-l00rnrn. braking excessively weak, the door hits the door frame at high speed, or, when the door stops moving in the reverse direction, it goes beyond the proper stopping point.
- Page 16 , H.II O' T.STR HO.I%I+S: open iftcllon ratchet or push- Set to the "short" side for a button switch system door. Half-open operation switch The half- open stroke can be chosen from the seven steps programmed between 12.5% to of the door stroke. 87.5% Selection between automatic switching of full and half opening...
Need help?
Do you have a question about the EDM18ZII and is the answer not in the manual?
Questions and answers