Advertisement
Quick Links
Advertisement
Summary of Contents for impulce 2 IT8017 Super Pullover
- Page 1 T8017 Super Pullover Assembly Instructions...
-
Page 2: Table Of Contents
Table of contents Important Safety Instructions--------------------------------- 1 Exploded View Diagram------------------------------------------ 2 Hardware List-------------------------------------------------- ------ Parts List----------------------------------------------------- ---------- Assembly instructions------------------------------------------... -
Page 3: Important Safety Instructions
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. When using exercise equip- ment, basic precautions should always be taken, including the following: * Read all instructions before using the Super Pullover These instruc- tions are written to ensure your safety and to protect the unit. -
Page 4: Exploded View Diagram
T8017 Super Pullover Exploded View Diagram... -
Page 5: Hardware List
Hardware List 1 10 14 0 Millimeters Inches... -
Page 6: Parts List
Parts List Item No. Description QTY Item No. Description Main Upright Allen Bolt M12×40 Low Cross Allen Bolt M10×100 Seat Support Allen Bolt M10×115 Upper Cross Allen Bolt M10×75 "L" Cam Allen Bolt M10×70 Allen Bolt M10×45 Allen Bolt M10×25 Handle Shoulder Bolt M8×30 Seat Pad Support... -
Page 7: Assembly Instructions
Assembly instructions Assembly of the Super Pullover takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recom mended to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. - Page 8 Step1 Install the Adj. Foot Plates Align the Adj. Foot Plates(#29) to the Main Upright(#1) and the Seat Support(#3), then secure them by hands.
- Page 9 Step2 Assemble The Frame 1)Attach the Low Cross(#2) and the Upper Cross(#4)to the Main Upright(#1) using: two Allen Bolts(#47) M10×100 two Allen Bolts(#48) M10×115 four Nylon Locknuts(#63) M10 eight Washers(#61) Φ 11× 20× Φ 2)Attach the Seat Support(#3) to the Upper Cross(#4) and the Low Cross(#2) using: four Allen Bolt(#50) M10×70 eight Washers(#61)
- Page 10 Step3 Assemble The Swivel Frame 1)Align the "L"Cam(#5) to the Upper Cross(#4) and sec- ure it using: one Shoulder Bolt(#56) M10×55 two Pulley Covers(#66) two Bronze Bushings ID 12(#75) one Nylon Locknut(#63) M10 2)Attach the Spring(#23) to the Upper Cross(#4) with the Nylon Locknut (#63), next hook the "L"...
- Page 11 Step4 Assemble The Pillow Block Attach the Pillow Block(#20) to the Main Upright(#1) using: two Allen Bolts(#46) M12×40 four Washers(#60) 13× 24×1.5 Φ Φ two Nylon Locknuts(#62) M12 two Spacers(#91) Φ 16× 12 2×12.5 Φ...
- Page 12 Step5 Assemble The Arm 1)Insert the Arm(#6) into the Main Upright(#1) and thro- ugh the Pillow Block(#20). 2)Attach the Counter Poise(#30) to the Pivot Arm(#6) using: two Shoulder Bolts(#53) M8×30 two Spring Washers(#65) Φ...
- Page 13 Step6 Assemble The Cam Insert the Arm(#6) through the Main Upright(#1), the Spacer(#19) and the Cam(#7),next, secure the Cam(#7) to the Arm(#6) using the Key (#37).
- Page 14 Step7 Assemble The Pillow Block 1)Insert the Short Spacer(#18) onto the Arm(#6) as sho- wn below. 2)Attach the Pillow Block(#20) to the Main Upright(#1) using: two Allen Bolt(#46) M12×40 two Nylon Locknuts(#62) M12 four Washers(#60) Φ 13× 24×1.5 Φ two Spacers (#91) Φ...
- Page 15 Step8 Assemble The Start Up Foot Frame Insert the Start Up Foot Frame(#10) into the Seat Sup- port(#3) and secure it using: one Allen Bolt(#52) M10×25 one Washers(#61) Φ 11× 20×1.5 Φ one Spring Washers(#64) Φ one Washer(#14)
- Page 16 Step9 Assemble The Weight Plates 1)Insert both the Guide Rods(#17) into the Main Upright (#1). 2)Slide the Weight Rubber Bumper(#32)down onto each Guide Rod(#17). 3)Carefully begin sliding the Weight Plate one by one in sequence:#40,#39,#38,#41 4)Align both top ends of the Guide Rods(#17) to the Main Upright(#1) and secure them using: two Allen Bolts(#50) M10×70 two Washers(#61)
- Page 17 Step10 Route The Cables 1)Put the clip tied on the weight pin leash onto the Top Plate(#41) as shown, next connect the Cable(#44) to the Top Plate(#41). 2)Route the Cable(#41) up and over the two Pulleies A (#69).then secure them to the Main Upright(#1) using two Allen Bolts(#51) M10×45 four Washers(#61) Φ...
- Page 18 For Step 10...
- Page 19 Step11 Assemble The Decal Plates 1)Attach the two Decal Plates(#15,#16) to the Main Up- right(#1) using: fourteen Butttons(#35) 2)Attach the Weight Shroud (#12) to the Main Upright (#1) using: four Bolt Covers(#71) four Plastic Washers(#59) four Chamfer Bolts(#70) The Front Decal Plate(#16) with the exercise instr- uctions printed on it should be attached in the front Note of the Main Upright(#1).
- Page 20 Step12 Assemble The Pads 1)Attach the Seat Pad(#22) to the Seat Support(#3) using three Washers(#61) Φ 11× 24×1.5 Φ two Allen Bolts(#77) M10×30 one Allen Bolt(#49) M10×75 2)Attach the Seat Pad(#21) to the Seat Pad Support(#9) using: two Allen Bolts(#77) M10 30 ×...