Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for inform Infocharger
- Page 1 Infocharger DC POWER SUPPLY/BATTERY CHARGER...
- Page 2 Important Notices! Thank you for choosing INFORM’s Infocharger system. This product can be used for both battery charger and DC power supply applications. For the staff and equipment safety it is necessary for the users to fully read and save this manual before working on this equipment.
-
Page 3: Table Of Contents
Contents Safety ..............................1 System Description ..........................2 Installation ............................. 4 3rd1 Handling .....................................4 3rd2 Storage....................................4 3rd3 Positioning..................................4 3rd4 Connections ..................................5 3rd4.1 Ground (Earth) Connection ...........................5 3rd4.2 Input connection...............................5 3rd4.3 Battery connection..............................5 3rd4.4 Output connection ..............................5 Switch On and Switch OFF procedures ....................6 4th1 System Switch ON ................................6 4th2 System Switch OFF ................................6 Operating Instructions ........................... -
Page 5: Safety
• In case of emergency (damage of the cabinet, front panel or connections etc.) switch off the battery charger, disconnect the input supply and inform the authorized technical service staff. • The unit should be packed properly if it is needed to be moved. -
Page 6: System Description
System Description DC Power Supply Operation Mode If the equipment is being ordered as DC Power Supply, then the unit supplies a limited voltage and current value that is adjusted from the front panel to the connected DC load. The output voltage and current limits can be easily adjusted separately from the SETTINGS menu on the LCD panel. - Page 7 Input and output EMI filters These filters prevent electromagnetic interference between Infocharger, mains and loads. (EMI – electromagnetic interference) Your battery charger and loads are protected against high voltage. Power Factor Correction When the power factor is 1, all the energy supplied by the source is consumed by the load DC / AC Inverter The inverter helps to obtain a very constant AC voltage level at the output by using DC voltage at the boost’s...
-
Page 8: Installation
Installation Check if the Infocharger has been subjected to any damage before unpacking it. If you notice any damage, please contact to transport firm. Check if all the additional parts have been supplied with the battery charger. Please make sure that the packing contains the following •... -
Page 9: 3Rd4 Connections
The grounding connection of the external battery cabinet(if any) should be done over the same battery grounding contactor. The connection between the grounding unit of the Infocharger and the ground can be made according to the minimum cross-sectioned cables which are given in the technical specifications table below. -
Page 10: Switch On And Switch Off Procedures
Switch On and Switch OFF procedures 4th1 System Switch After making all the connections mentioned in the previous chapter, you need to switch on to all the automatic fuses on the front panel, if mains voltage is within the limits, the unit switches on. Inforcharger makes self-test for few seconds to check if everything is normal, and then starts to charge the batteries or supply the load. -
Page 11: Operating Instructions
5th1 Unit Operation 5th1.1 Operation modes • Infocharger; is designed for the usage as a battery charger and dc power supply. Output current, voltage and the float charge limits are adjustable on the front control panel easily. The battery current and voltage characteristics are shown in the figure below... -
Page 12: 5Th2 Displays
5th2 Displays The front panel of the Infocharger is shown below: Infocharger control panel is composed of; • LCD Display (Liquid crystal display), • LEDs • Buttons 5th2.1.1 LCD Display There are mainly four display sections on the control panel as follows... - Page 13 0-30, 0-60, 0-140 VDC . Iout : It is adjustable between 0-255, the current is adjustable between values 0-60, 0-30, 0-15 A according to the type of Infocharger. If CH mode is selected -(Battery charger) Battery capacity: It is between 0-1000 Ah...
-
Page 14: 5Th2.1.2 Buttons
There are mainly four buttons in the front panel. The functionalities of the buttons are given below. button: Scroll down to next line button: Scroll up to previous line button: Exit from the active menu. button: Enter to active menu. TREE STRUCTURE OF THREE PHASE INFOCHARGER MENU SCREEN Vbat XXX V MENU MENU... -
Page 15: Optional Modules
Optional Modules There are mainly two optional modules for the Infocharger These are; 1- LVD Module: This module prevents the loads and batteries to be deeply discharged. A delay is used for the separation of the batteries from the load. This delay is on L+ side. The voltage level of this separation process can be chosen on the control panel. -
Page 16: Maintenance
Maintenance The Infocharger unit does not need maintenance. If you want to make cleaning on the unit, than you should perform the following: • Disconnect the loads • Bring all the fuses on the unit to “0” position. • Clean the unit with a slightly moistened cloth. -
Page 17: Trouble Shouting
Trouble Shouting • In this section, procedures that should be followed, explained during an abnormal condition of the unit. Before your inform the technical service, read and apply carefully things explained in detail in this section. • If the fault led on front panel is on; then go to the main menu on front panel and check what the fault is. -
Page 18: Technical Specifications
Technical Specifications Dimensions Height 28 cm Width 25 cm Depth 42 cm Weight 11,6 kg Environmental Conditions Operating 0 ... +50 [°C] Operating %20 ... %80 Temperature Relative Humidity Storage -15 ... +70 [°C] Storage %20 ... %95 Electrical Specifications Connection cable’s section area BATTERY INPUT... - Page 19 Dynamic response 2%< 2%< 2%< 2%< Electronically short circuit protection / over current protection / Output protection reverse voltage protection Standards IP 20 Protection Class EN 50091-2 Performance EN 62040-3, EN 50091-3 Safety EN 50091-1 Product Certification CE, TSEK INFOCHARGER...
- Page 20 Cable cross-section area (mm2) Current value absorbed by t he load(Amp.) THESE UNITS ARE GIVEN FOR THE MULTI-VEINS CABLES. INF561-Y01-U105-1-00...
- Page 21 THE INFOCHARGER BLOCK DIAGRAM A 2.5mm2 B 16 mm2 C 16 POLE FLAT D 20 POLE FLAT OPSIYON E 2 POLE 0.25mm2 ISARETSIZ 0.5mm2 POWER LVD K1 X102 X103 RELAY X101 MAIN CONTROL BOARD X403 X403 CONTROL X101 X101 2 1...
Need help?
Do you have a question about the Infocharger and is the answer not in the manual?
Questions and answers