Table of Contents
Advertisement
Quick Links
User guide
TP09D
Analogue Test Telephone
Version 3
© KURTH ELECTRONIC GmbH
All rights reserved, including those of the translation
Reprint and data processing, also in extracts, only with written permission
of Kurth Electronic GmbH
All trademarks and logos mentioned herein belong to their registered owners
Kurth Electronic GmbH | Muehleweg 11 | D 72800 Eningen u.A. GERMANY |
Tel. +49(0)7121 9755 0 | Fax +49(0)7121 9755 56 |
info@kurthelectronic.de | www.kurthelectronic.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Kurth Electronic TP09D
- Page 1 Kurth Electronic GmbH All trademarks and logos mentioned herein belong to their registered owners Kurth Electronic GmbH | Muehleweg 11 | D 72800 Eningen u.A. GERMANY | Tel. +49(0)7121 9755 0 | Fax +49(0)7121 9755 56 | info@kurthelectronic.de | www.kurthelectronic.de...
- Page 2 FLASH off Hook Off Hook (pick up) Flash button (flash times selectable in the menu) On Hook (hang up) Speaker mode SPKR ON-OFF Volume + Volume - Battery compartment lid Speaker Test cords with 6-ANB clips A- and B-core © Kurth Electronic GmbH, All Rights Reserved...
-
Page 3: Main Functions
The TP09D is a rugged and waterproof analogue test phone with a back- lit graphic display, protected keyboard, menu-driven operation and caller ID (CLIP), message waiting indicator (MWI), DTMF grabbing, line voltage and current, high-impedance monitor, overvoltage and undervoltage lockout, data... - Page 4 RING mode (on Hook) – normal operating mode Incoming call (default) In the default setting on Hook, the TP09D waits for a call. The sequence and volume of the sound signal can be adjusted in the setup menu. Immediately after the first incoming call, the device is automatically switched on and „listens“ to the line. If the line transmits CLIP data in FSK format, it is evaluated and shown on the display.
- Page 5 TALK mode (off Hook) – normal operating mode Outgoing call When the TP09D is switched on, after pressing the off Hook key, the line voltage is first measured in order to prevent inadvertent occupancy of the line when the Low Voltage Lockout is activated. If the measured line voltage is between 2 and 75 volts, the information No line disappears and the line is occupied.
- Page 6 RCL), name and time and date (CID RCL only) of the last call are displayed in sequence. The last three calls or calls are displayed by pressing the key repeatedly. Press SEL to dial the number on the display. The TP09D has a total of 12 memory locations.
- Page 7 ON / OFF (Advanced funtions) For further functions, the TP09D is switched on using the red ON / OFF key (keep the key pressed for more than one second). The following functions can be selected:...
-
Page 8: Menu Structure
12 kHz 16 kHz Line test mode Low Voltage Inhibit Ringer mode Slow Fast High 10 Language English German 11 Backlight 12 Flas times 100 ms 270 ms 600 ms 13 Exit Exit © Kurth Electronic GmbH, All Rights Reserved... -
Page 9: Monitor Mode
The CID RCL key stores all transmitted information of the last three calls (e.g. phone number, name, date and time), if offered by the network operator. In talk mode, the stored information can be recalled by pressing the key repea- tedly and selected with SEL. © Kurth Electronic GmbH, All Rights Reserved... - Page 10 SMS can only be received if the correct SMS Center phone number for the service provider is entered in the setup menu and the service is activated. Activation and deactivation can be carried out in the menu. © Kurth Electronic GmbH, All Rights Reserved...
- Page 11 TP09D. DTMF-Grabbing In monitor mode, the TP09D can decode the number dialed by another de- vice on the line (e.g. fax, modem or other terminal) and display up to 48 digits (DTMF dialing only).
-
Page 12: Saving Phone Numbers
LNR or CID RCL key, scrolling through the stored numbers each time the key is pressed. If MR is selected, followed by a number key, the correspon- ding number is retrieved from the respective speed dial memory. The number is dialled with SEL. © Kurth Electronic GmbH, All Rights Reserved... - Page 13 To replace the test cords, open the battery compartment. The cover simulta- neously holds the test cords in the housing. When it is removed, the test cord can be pulled out. The connections are screwed and can be opened easily. © Kurth Electronic GmbH, All Rights Reserved...
-
Page 14: Insert / Replace Battery
Make sure the polarity is correct when inserting the battery. Use only good quality batteries. The TP09D is waterproof. Only the battery com- partment and the test cord connection area are not protected. If water has penetrated into the TP09D, this area must be dried. -
Page 15: Technical Specifications
1 50 cm long test cords made of flexible PVC with crocodile clips, exchangeable on site Strain relief of the test cords Separate battery compartment with captive screw Dimensions 250 x 80 x 30 / 70 mm Weight 450 g with battery © Kurth Electronic GmbH, All Rights Reserved... -
Page 16: Safety Instructions
IP 54 Safety instructions The TP09D may only be operated with the accessories originally pro- vided. Using the device with accessories that are not original or for ap- plications for which it was not intended can lead to incorrect measure- ments and may damage the device.
Need help?
Do you have a question about the TP09D and is the answer not in the manual?
Questions and answers