Table of Contents
Advertisement
Product User Manual
http://www.calb.cn/ | http://en.calb.cn/
Annex 2: Instructions for CAM Series battery protection components installation ...................... 17!
China Aviation Lithium Battery Co,. Ltd.
CALB Headquarter:
No. 66 North Binhe Road, High-Tech Zone, Luoyang, Henan, China 471003
Tel ：(86)0379-6069 7962
Fax：(86)0379-6069 7995
Advertisement
Table of Contents
Related Manuals for CALB CAM72
Summary of Contents for CALB CAM72
- Page 1 Product User Manual http://www.calb.cn/ | http://en.calb.cn/ Annex 2: Instructions for CAM Series battery protection components installation ...... 17! China Aviation Lithium Battery Co,. Ltd. CALB Headquarter: No. 66 North Binhe Road, High-Tech Zone, Luoyang, Henan, China 471003 Tel ：(86)0379-6069 7962...
-
Page 2: Table Of Contents
Developing green energy is our common history mission. Under the strong support IV. Transportation requirements ........................8 of leaders at all levels and partners, CALB will take the idea of AVIC —“ Aviation to serve the country , strengthen the army and enrich the common”, and follow the IIV. -
Page 3: Caution
1.1 Product Introduction The lithium-ion batteries produced by CALB have the advantages of high energy density, long life cycle, high power density, high security, even good performance under low temperature. Based on the different case material,the CALB battery can be sorted to molded battery, metal shell batteries, soft pack batteries. -
Page 4: The Structure Of Battery
3) Integrate battery modules into group according to the maximum possible number of cells that a individual BMS sub-module can 3) CALB lithium-ion battery products shall be equipped with a special lithium battery management system and lithium battery charger manage ablity. -
Page 5: Power System Maintenance Period And Measures
Product User Manual 1. Basic Inroduction Terminal bolt specification recommended tightening torque（N·m） 3) For the automotive module or portable module application, appropriate measures of shock absorbing shall be taken. 4) Leave enough adequate space above the battery module inner the battery box ,to connect the battery management system harness line, also for better heat dissipation. -
Page 6: Emergency Treatment
Product User Manual 1. Basic Inroduction 3. Emergency treatment There are lithium salt compounds, organic solvents, etc. inside the lithium-ion batter- 4) Electrolyte Ingestion: Take 2 cups of milk or water orally. Do not induce vomiting unconsciously. Go for medical treatment in ies. -
Page 7: Iiiv. Customer Services
IIIV. Customer Services Time requirements: For customers in China mainland, CALB will response in two hours within the city, in 24 hours within the province, three working days or within 30 minutes to give customers a clear answer and reach to the customers within the appointed time outside the province. -
Page 8: Annex 2: Instructions For Cam Series Battery Protection Components Installation
1. Overview This instruction is only applied for the installation of plastic protection components in CAM series Li-on prismatic cells manufactured by CALB. 2. Installation for CAM Series battery protection components The protection components for CAM Series are injected molding by flame-retardant ABS + PC material, with flame retardant grade level V0, thus protecting battery in the metal shell from instability under shock, impact, high pressure and others. - Page 9 Product User Manual Step 2: Install grouping separators as figure 3. Step 4: Install the pole protector as figure 5. Pole protector Upper protector Grouping separator Grouping separator Lower protector Lower separator Figure 5 Figure 3 Installation requirements: Installation requirements: Press the pole protector into the upper protector from up to down, and clamp the protectors by the snaps on both sides without Push the battery grouping separators by one side, and clamp the battery by the snap on both sides without falling down.
- Page 10 Product User Manual Installation for the battery pack can be followed as five steps. Step 4: Install the bus bar. Assemble the bus bars according to grouping way, as figure 10. The first step: Arrange the single batteries equipped with protection components and fastening clamps in alignment (take 3 batteries for example);...
Need help?
Do you have a question about the CAM72 and is the answer not in the manual?
Questions and answers