Summary of Contents for YanLing Intel Celeron N3160
- Page 1 研凌工控电脑科技 ( 深圳 ) 有限公司 YL-N3160 L2 V2 mainboard User manual Intel Celeron N3160 processor Copyright:2017.9 1.2...
-
Page 2: Chapter I:hardware Installation
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter I:Hardware installation Precaution before installation The motherboard is made up of many sophisticated integrated circuits and other components that are easily damaged by static electricity, Please read the manual and prepare the following instructions before installation: Please confirm that the size of the chassis is consistent with the motherboard before installation. - Page 3 研凌工控电脑科技 ( 深圳 ) 有限公司 avoid Board damage or failure. Please make sure that no screws or metal in or on the motherboard inside the computer chassis. Do not place the computer in unstable.
-
Page 4: Chapter Ii Instruction Of Mainboard
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter II instruction of mainboard Size 12cm*12cm Chipset Intel Celeron N3160 CPU frequency Quad core，1.6GHz，2M second level cache，power dissipation：6W Memory slot 1 x DDR3L 1600 SODIMM，Max.8G Intel HD Graphics 400 SATA port 1 x SATA 3.0 USB port 4 x USB 2.0，2 x USB 3.0... -
Page 5: Chapter Iii I/O For Mainboard
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter III I/O for mainboard Battery WIFI/4G SIM slot RAM slot MSATA SATA PWR SATA COM1 USB2.0 USB3.0 Power DC 12V HDMI LAN1~2 Audio... -
Page 6: Chapter Iv Pin Definition
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter IV PIN definition Identifying Detail Remark HDD_LED+ PWR_LED+ HDD_LED- PWR_LED- RST_GND PW_ON PWON_GND 空 JSATA SATA power supply +12V +12V... -
Page 7: Chapter V Bios Setting
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter V BIOS setting 1、open PXE function Power on and then click DEL button enter BIOS setting, follow white option, choose “Advanced” → “CSM Configuration” → “Network” → “Legacy” ， “F4” → “YES” Esc. 2.close opening LOGO Power on and then click DEL button enter BIOS setting, follow white option, choose “Boot”... - Page 8 研凌工控电脑科技 ( 深圳 ) 有限公司 3、Closed LOGO setting Choose “Boot”——“Quiet Boot”——“Disabled”，and then clock“F4”——“YES” Esc. 4、PXE booted setting 4.1、start machine and click“DEL”，enter to BIOS setting，choose“Advanced”→“CSM Configuration”； 4.2、Network change to“Legacy”，choose“F4” save and Esc 4.3、click again“DEL” enter to BIOS，let“PXE”boot to be boot option 1 as follow picture；...
-
Page 9: Chapter Vi Watch Dog Setting
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter VI watch dog setting length Register specification name I/O address Address access register IoIndexPort 8bits 0x2E Data access register IoDataPort 8bits 0x2F Register specification name length IO address Device choose register DevSel 8bits 0x07 Watch dog controls register Bit7: 1=second mode WDTCtl... - Page 10 研凌工控电脑科技 ( 深圳 ) 有限公司 #define DataPort 0x2F #define DevSel 0x07 #define WdtCtl 0x72 #define WdtCount 0x73 #define WdtDevNum 0x07 UINT8 Temp; write a special value into the configuration mode IoWrite8(IndexPort, 0x87); IoWrite8(IndexPort, 0x01); IoWrite8(IndexPort, 0x55); IoWrite8(IndexPort, 0x55); // choose watchdog IoWrite8(IndexPort, DevSel);...
-
Page 11: Chapter Vii Common Hardware Failures And Troubleshooting
研凌工控电脑科技 ( 深圳 ) 有限公司 Chapter VII COMMON HARDWARE FAILURES AND TROUBLESHOOTING METHODS Problem check 1. make sure power supply correct connection 2. make sure power supply is available with machine 3. take out RAM and reset it Power on but machine 4. - Page 12 研凌工控电脑科技 ( 深圳 ) 有限公司 1、make sure USB device doesn’t need individual power on Cant find USB 2、make sure USB p o r t i s g o o d device 3、make sure USB controller is open into BIOS Setup...