Sukup Spredway Owner's Installation And Operation Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Spredway

Installation and Operation Manual

Website: www.sukup.com

ATES

12/05/2017 – Updated operation instructions ....................................................................................................... 10

Manual L1431

12/05/2017

Owner's

Sukup Manufacturing Co.

1555 255th Street, Box 677

Sheffield, Iowa, USA 50475-0677

Phone: 641-892-4222

Fax: 641-892-4629

E-mail: info@sukup.com

EVISIONS

AGES

Table of Contents

Need help?

Do you have a question about the Spredway and is the answer not in the manual?

Questions and answers

Summary of Contents for Sukup Spredway

Page 1 Spredway ® Owner’s Installation and Operation Manual Sukup Manufacturing Co. 1555 255th Street, Box 677 Sheffield, Iowa, USA 50475-0677 Phone: 641-892-4222 Fax: 641-892-4629 Website: www.sukup.com E-mail: info@sukup.com ATES EVISIONS AGES 12/05/2017 – Updated operation instructions ....................... 10 Manual L1431 ©Sukup Manufacturing Co.
Page 2: Table Of Contents
Table of Contents TABLE OF CONTENTS Proper management is essential to ensure satisfactory performance. Sukup Manufacturing Co. is not liable for damage to grain resulting from improper management during drying or storage. Limited Warranty ........................... 3 Safety Section ..........................4 Assembly ............................
Page 3: Limited Warranty
Limited Warranty...
Page 4: Safety Section
Sukup Manufacturing Co. via mail at PO Box 677, Sheffield, Iowa USA, 50475; by phone at 641-892-4222; or by e-mail at info@sukup.com. It is the responsibility of the owner/operator to know what specific requirements, precautions, and work Failure to follow precautions above will result in death hazards exist.
Page 5 Safety Section WARNING: Metal is slippery when wet. To To avoid electric shock or electrocution, all equipment must be properly wired and grounded avoid falls, never carry items if climbing on according to electrical codes. Have unit wired by bin. Maintain secure hand and foothold if climbing on qualified electrician.
Page 6 To order a replacement decal or shield at no charge, contact your dealer or Sukup Manufacturing Co., Box 677, Sheffield, IA USA 50475. If replacement is necessary, make sure location for decal is free from grease, oil and dirt.
Page 7: Assembly
1. Bolt motor to motor mount using four 5/16 x 1" bolts, nuts and lock washers. Align motor pulley to flat pulley by sliding on motor shaft. NOTE: Align belt when Spredway is in operating position. 2. Place belt on pulleys. Bend belt hook around belt as shown.
Page 8: Installation
Bolt, 5/16 - 18 x 1”, PLT J0527 Fig. 4 – Super High-Capacity Lock washer, 5/16" J1200 Nut, 5/16" - 18 J1002 *If bin’s fill ring is too small for Spredway to fit through, use a winch to raise it from inside of bin.
Page 9 J0527 Lock washer, 5/16" 9-15 J1200 Nut, 5/16” – 18, PLT 9-15 J1002 Fig. 6 – MFS bracket *If bin’s fill ring is too small for Spredway to fit through, use a winch to raise it from inside of bin.
Page 10: Operation
If grain is too low in center, rotate cover to make opening larger. IMPORTANT: When looking from top down, make sure spreader is turning counterclockwise. WARNING: Disconnect power before adjusting Spredway after installation. Contact with rotating pans could cause death or serious injury. TROUBLESHOOTING PROBLEM...
Page 11: Specifications
19" x 12" 19" x 13" BIN DIAMETER 18' - 33' 24' - 48' 36' - 60' WIRING Provide heavy-duty wiring to Spredway motor. Follow applicable electrical codes. Operating voltages for Spredway motors are listed below. FACTORY ALTERNATIVE MOTOR TYPE PRE-WIRED VOLTAGE*...
Page 12: Parts Identification
Parts Identification PARTS IDENTIFICATION Standard and High Capacity Spredway – Galvanized (G01051)
Page 13 Parts Identification Standard and High Capacity Spredway – Galvanized (G01051), Parts List All parts except those designated as “Standard” or “High Capacity” are interchangeable between Standard and High Capacity spreaders. REF. # DESCRIPTION QTY. COMP. # Locking handle G0112 Pre-spread ring w/knockouts G0182 Pre-spread disc, 3-1/2”...
Page 14: Super High Capacity Spredway - Galvanized (G0250)
Parts Identification Super High Capacity Spredway – Galvanized (G0250)
Page 15 Parts Identification Super High Capacity Spredway – Galvanized G0250, Parts List REF. # DESCRIPTION QTY. COMP. # Locking handle, 1/2 x 5-1/2" G0112 Pre-spread disc, Standard G0113 Flat pulley, 16" G0116 Pan pitch adjusting rod G0121 Pan hinge pin G0122...
Page 16: Contact Information
Contact Information CONTACT INFORMATION Owner’s manuals are available from Sukup Manufacturing Co. Additional copies can be requested at address, phone number or e-mail address shown below. Please indicate manual number L1431 when requesting Spredway Owner’s Installation and Operation Manual. Sukup Dealer Information...