Zamel RTM-30 Instruction Manual

RTM-30 TEMPERATURE REGULATOR
Zakład Mechaniki i Elektroniki
J.W. Dzida, K. Łodzińska
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04
www.zamelcet.pl, e-mail: marketing@zamel.pl
DESCRIPTION TEChNICAL DATA
The temperature regulator operation is
based on heating/regulation curve which we
obtain by means of choosing points inclu-
ding both the expected temperature and the
reference temperature, by choosing a ready
made curve or by changing options for room
regulation. The regulator preserves the tem-
perature with the heating source suitable for
the reference point (e.g outer or inner tem-
perature), chosen during configuration pha-
se. Regulation algorithm causes the heating
Temperature regulation adjustment range: 5 ÷ 95
costs lower and the same gives full comfort of
room and weather regulation. The regulator
uses two sensors for proper operation. There
is also a possibility of extending its existing
connection cable up to 50 m with a cable sec-
tion of 0,2÷2,5 mm 2 . The reference tempera-
ture sensor can be replaced with a standard
resistor, which causes one sensor operation
as in the standard temperature regulation.
The regulator is a perfect solution in eve-
ry situation we want to be sure there was a
Regulator ambient temperature range: -20 ÷ 60
full factor ciculation e.g.: cooling systems or
heating systems, but also in situations where
suitable temperature difference is necessary
for preserving best conditions with maximum
low costs e.g.: hot water circulation. Repla-
cing one temperature sensor with a standard
resistor has the effect of constant regulation
around one point in accordance with the ad-
justed curve, close to the chosen points.
Replacing one temperature sensor with a
potentiometer with similar functions has the
effect of changing a universal regulator into a
standard temperature regulator with differen-
ce regulation possibility by means of curve
and hysterisis. It allows to control, e.g., the
heating source in such a way its temperature
is higher than the adjusted one including dif-
ference corresponding e.g. the ambient tem-
APPEARANCE
perature loss through windows, etc.
CEChy
● Temperature level regulation in the range
of 5 ÷ 95 °C,
● two external temperature sensors,
● LCD display and keypad,
● output receiver's temperature regulation in
accordance with the reference temperatu-
re,
● output receiver's temperature regulation in
accordance with temperature differences,
● heating sources economical regulation
gives enormous savings during heating
period,
● simultaneous regulation possibilities of
cooling and heating sources,
● temperature regulation possibility by
means of blending valves,
● replacing possibility of a reference tempe-
rature regulator with a standard resistor,
The symbol stands for selective
● double-modular casing with a shield,
collection of electrical and
● TH-35 DIN rail installation, electronical devices. It is
forbidden to place the used
● two output relays of max 16A capacity.
devices with other waste.
MANUAL INSTRUCTION
ZAMEL sp.j.
RTM-30
Power supply terminals: A1, A2
Input rated voltage: 85 ÷ 265 V AC
Nominal frequency: 50 / 60 Hz
Rated power consumption: < 1,5 W
Temperature sensor terminals: T1 (t reference), T2 (t expected)
Temperature sensor type: KTY 81-210
o C
Hysteresis: +/- 0,5 C
o
Relay output (supply) terminals: 11, 12, 14, 21, 22, 24
Receiver switch on indicator: LCD
LCD display backlight: amber
Output relay parameters: 2NO/NC 16A / 250V AC1 4000VA
Number of terminal clamps: 12
Section of connecting cables: 0,2 ÷ 2,50 mm
2
o C
Sensor ambient temperature range: -20 ÷ 90
o C
Operating mode: freely
Mounting: rail TH35 (acc to PN-EN 60715)
Protection degree: IP20 (PN-EN 60529)
Protection level: II
Overvoltage category: II
Pollution degree: 2
Dimensions: double-modular (35 mm) 90x35x66 mm
Weight: 0,160 kg
Reference standards: PN-EN 60730-1; PN-EN 60730-2-7
PN-EN 61000-4-2,3,4,5,6,11
Power supply
Temperature sensor clamps
terminals (A1, A2)
LCD display
Control push buttons
Relay output (supply) terminals
(12, 11, 14, 24, 21, 22)
MOUNTING
1. Disconnect power supply by the pha-
se fuse, the circuit-breaker or the
switch- disconnector combined to the
proper circuit.
2. Check if there is no voltage on con-
nection cables by means of a special
measure equipment.
3. Install the RTM-30 on the TH-35 DIN
rail in the switchboard.
4. Connect the cables with the termi-
nals in accordance with the installing
diagram.
5. Switch on the power supply from the
mains.
INNER DIAGRAM
μC
DIMENSIONS
FAMILy PRODUCT
RTM-30 temperature regulator belongs
to RTM family product.
RTM - xx
Device type:
01 - basic
02 - LCD display
(T1, T2)
03 - weather with LCD
Device symbol
WARRANTy CARD
There is 24 months guarantee on the product
Salesman stamp and signature, date of sale
VER. 002_20.05.2010
CONNECTION
L
N
LCD
RTC
APPLICATION
L N
display
1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.
2. The manufacturer's guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modifications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer.
3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.
4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.
5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer's guarantee is valid in the Republic of Poland.
7. The PURCHASER's statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.
Heating
Cooling
Outer temperature sensor
RTM-30 regulator
Room temperature sensor
Floor heating
Air-conditioner