Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for SERVETTO 3-Z15 Series
-
Page 2: Table Of Contents
5 CONNECTI ON OF THE ELECTRI C SERVETTO 5.1 USE AND PROGRAMMI NG OF THE REMOTE CONTROL 5.2 PROGRAMMI NG OF THE REMOTE CONTROL 5.3 FI RST USE OF THE ELECTRI C SERVETTO 6 DI SPOSE 7 ECOLOGY 8 WARRANTY CONDI TI ONS... -
Page 3: Ntroducti On
Children should be supervised to ensure that they do not play with the appliance. Do not connect the electric Servetto to the mains supply if the plug or the transformer power cable (F) are damaged. Unplug the electric Servetto when unused for long periods of time. - Page 4 Voltage signal led 2 – Radio programming signal led 3 – Radio programming button 4 – Button for using the electric Servetto without the remote control and for emergency stop (Please use this button just in case of emergency) Fig. 2...
-
Page 5: Di Mensi Ons
Electric Servetto 3.2 DI MENSI ONS Fig. 3 Place the control unit far from damp spaces. For a correct installation of the cables, it is necessary to maintain the safety distances The transformer must always be approachable in case of maintenance. -
Page 6: Wi Ri Ng Layout
3.4 USE OF THE SECURI TY SENSOR The use of at least one security sensor is necessary for the use of the electric Servetto. I n case of a two doors wardrobe, we recommend the use of two security sensors, one for each wardrobe side. -
Page 7: I Nstallati On Examples
Electric Servetto 3.5 I NSTALLATI ON EXAMPLES Wiring at sight with control unit and transformer fixed to the back of the wardrobe (or under the shelf) . Fig. 7 Unsight wiring, with control unit and transformer fixed above the wardrobe. -
Page 8: Nstallati On
4 I NSTALLATI ON 4.1 DRI LLI NG AND I NSTALLATON OF THE FI XI NG PLATES Fig.9... - Page 9 Electric Servetto Drilling instructions by using the supplied template. Fig. 10 Fig.11...
-
Page 10: Dri Lli Ng And I Nstallati On Of The Securi Ty Sensor
Fig. 12 4.2 DRI LLI NG AND I NSTALLATI ON OF THE SECURI TY SENSOR Fig. 13... -
Page 11: I Nstallati On Of The Lateral Arms
Connect the transformer to the electricity network, then connect the transformer to the control unit, the green voltage signal led must now turn on. Once the transformer is connected to the electricity network, the electric Servetto makes the reset, a sound signal indicates that the electric Servetto is now ready to use. -
Page 12: Connecti On Of The Electri C Servetto
When not used, the remote control goes into standby mode. To reactivate it, press the button on the right side of the remote The electric Servetto works only pressing the button SERV. By pressing the arrow mark , you can select the wardrobe compartment. -
Page 13: Programmi Ng Of The Remote Control
5.2 PROGRAMMI NG OF THE REMOTE CONTROL (OPTI ONAL) I n order to connect the electric Servetto with the remote control, please follow this procedure: - Press the programming button (Fig.18) and when the led signal turns on, release the button. -
Page 14: Di Spose
Once you have checked that the lateral arms are parallel, block the adjustable clothes tube, by turning the two pieces of the tube, then tighten the screws of the angular pieces. Press again the button SERV, the electric Servetto now goes up. -
Page 15: Warranty Condi Ti Ons
This product has been submitted to strict control testing by the manufacturer, in accordance with the actual international standards. We are thus sure of its high quality. If the Servetto Elettrico does not work correctly, we kindly ask you to contact the retailer where you have bought it for assistance.
Need help?
Do you have a question about the 3-Z15 Series and is the answer not in the manual?
Questions and answers