CET RTS-01 Instruction Manual

MATEC – ELECTRIC HEATING SYSTEM
TEMPERATURE COTROLLER RTS-­01
DESCRIPTION
RTS-­01 temperature controller is not a pro-­
ing. The device cooperates with electric and
trol temperature by means of (internal) built-­in
temperature cotroller
heating mat
The regulator should be installed:
or installation cable box Ø60 mm);; 120
blows.
FEATURES
economical and comfort mode operation;;
optional temperature display: Celsius or
Fahrenheit (temperature) scales;;
temperature control by means of (internal)
easy, intuitive service.
The device is designed for single-­
phase installation and must be installed
in accordance with standards valid in a
particular country. The device should
CAUTION!
be connected according to the details included in
this operating manual. Installation, connection and
cian staff, who act in accordance with the service
manual and the device functions.
In case of casing dismantling an electric shock
may occur, and the guarantee is lost then. Before
installation make sure the connection cables are
not under voltage. The cruciform head screwdriver
3,5 mm should be used to instal the device. Im-­
proper transport, storage, and use of the device
to instal the device in the following cases: if any
device part is missing or the device is damaged or
deformed. In case of improper functioning of the
device contact the producer.
The symbol means selective collecting
of electrical and electronic equipment.
It is forbidden to put the used equip-­
ment together with other waste.
tel.: +48 (32) 449 15 00;; fax: +48 (32) 449 15 02
TECHNICAL DATA
-­
Input (supply) terminals: L (5), N (6)
-­
Nominal power consumption:
Room temperature adjustment range: +5 ÷ +30 °C
Floor temperature control range: +5 ÷ +40 °C
Accuracy of temperature measurement: ±1 °C
Number of terminal clamps: 6
Section of connecting cables: 0,5 ÷ 1,5 mm
Ambient temperature range: -­5 ÷ +50
Casing protection degree: IP21
APPEARANCE
Adjustment knob
-­
Main switch
Base mounting screw
Temperature sensor terminals
Modes operation switch
Relay output terminals
Input (supply) terminals
CET Sp. z o.o.
43-­200 Pszczyna, ul. Zielona 27
e-­mail: matec@cet.pl
www.zamelcet.com
RTS-­01
Input rated voltage: 100 ÷ 240 V~
Nominal frequency: 50 / 60 Hz
Battery support: none
NTC senor terminals: RT+, RT-­
Temperature senosor: NTC 100 k for 25 ºC
Relay parameters: 5 A / 230 V~
o
Casing mounting: surface
Protection level: II
Overvoltage category: II
86 x 86 x 38 mm
Weight: 0,114 kg
Reference standard: PN-­EN 60730-­1:2002, PN-­EN 60730-­2-­9:2006,
PN-­EN 61000-­3-­2, PN-­EN 60730-­3-­3,
PN-­EN 55022, PN-­EN 61000-­4-­3,
PN-­EN 55014-­1:2007+A1:2010,
PN-­EN 61000-­4-­4, PN-­EN 61000-­4-­5,
PN-­EN 61000-­4-­11, PN-­EN 61000-­4-­2,
PN-­CISPR 16-­2:1999,
PN-­CISPR 16-­1:1997+A1:2000
MANUAL INSTRUCTION
2
C
VER. 001_04.07.2011