Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for FIELDQUIP XGB Series
- Page 1 XGB Series Graderblade OWNER/OPERATOR MANUAL...
- Page 2 Farm Machinery Safe Work Practices, prior to the equipment being placed in service. Fieldquip warrants new products sold but it to be free from defects in material and workmanship for a period of twelve months for farmers or lifestyle applications after delivery to the initial user. This warranty is for the replacement or repair of any part found to be defective during the warranty period.
- Page 3 DESCRIPTION The XGB Series Hydraulic Grader Blade by Fieldquip is a three point linkage tractor mounted implement designed for leveling, and back filling in small areas such as outdoor arenas, small feed lots, drive ways and farm lanes. Please ensure the unit you have purchased has the horse power rating to match that of your tractor.
-
Page 4: Purpose Of This Manual
PURPOSE OF THIS MANUAL The purpose of this manual is to assist you in operating and maintaining your Fieldquip implement. Read it carefully. It provides information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to the unknown and varying operation conditions. -
Page 5: Specifications
Each machine comes with its own serial number plate which will show the model and serial number starting with FQ this number identifies the implement for spare parts enquires and for completion of your warranty form. Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care... - Page 6 Use extreme care when working close to fences, ditched, hillsides or other obstacles. Do not operate or transport on steep slopes. If in doubt set rear axles wider for moderate slopes. Never leave a tractor and implement running unattended. Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care...
-
Page 7: Operation
Block implements securely for storage. Keep children and by standers away from storage area. Fieldquip Australia accepts no responsibility or liability for any losses, injuries or damage that may result from failing to observe these safety rules and the safety decals on the implement. -
Page 8: Operating Technique
Pass diagonally through sharp dips and avoid sharp drops. Best performance can be achieved at an approximate speed of 3-6km/hr. Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care... - Page 9 When blocking, you must consider the overall stability of the implement. Just placing jack stands under the unit will not ensure your safety. The working surface must be level and solid to support the weight Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care...
-
Page 10: Maintenance
Turn tractor engine off, remove key, apply hand brake, chock wheels and disconnect PTO Shaft from the tractor before performing any service or maintenance. Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care... -
Page 11: Spare Part List
Install leveling wheel. Unable to hold level Tractor and blade follow contour. Install leveling wheel. ground. Tractor draft control lifting blade. Set tractor draft control. SPARE PART LIST Diagram needed here Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care... -
Page 12: Pre Delivery Checklist
Check all cotter pins and linkage pins and ensure they are properly installed and can be secured Check that any “wear points” (i.e. Points, blades, edges, tines) have been properly installed. Fieldquip Pty Ltd …Australian owned family business…smarter gear…smarter care... -
Page 13: Warranty
(iii)The machine is worked within its stated capacity (ie. Horsepower limit and PTO Speed), (iv) The machine is not subjected to any modifications or damage from improper use, (v) Fieldquip is in receipt of duly signed pre- delivery and installation certificate and warranty documentation. -
Page 14: Warranty Procedure
All claims will be nul and void if any warranty work is commenced without prior approval from Fieldquip. WARRANTY PROCEDURE Contact Dealer who will contact Fieldquip Photos of repair required emailed to warranty@fieldquip.com with description of problem... - Page 15 Fieldquip will not recognise any work carried out without a warranty claim number. DELIVERY, WARRANTY AND SAFETY ACKNOWLEDGEMENT To be completed by the dealer and purchaser at the time of delivery and returned to Fieldquip Dealer Name and Address: ………………………………………………………………………………………………………………………………...
- Page 16 8. I have discussed the approved codes of practice which apply to this type of machine. 9. I will arrange to return this form to Fieldquip for registration within 14 days of sale along with the warranty card. Name: …………………………………………… (Block Letters) Position Title: …………………………...
Need help?
Do you have a question about the XGB Series and is the answer not in the manual?
Questions and answers