Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Taylor Tools Bronco 260 Electric
- Page 1 Bronco Floor Removal Machine Owners Manual Rev. 6/07...
-
Page 2: Table Of Contents
Mr. Donald Pope. Mr. Pope developed this machine over a 5 year period to improve floor removal rates for his business in Ocilla, Georgia. Donald has joined forces with Taylor Tools to assist us in bringing you this remarkable floor removal machine. -
Page 3: Safety Alert And Notations
Safety Alert Symbol and Notations READ AND UNDERSTAND THIS IMPORTANT SAFETY INFOR- MATION BEFORE OPERATING THIS MACHINE! This safety alert symbol is used to attract your attention because PERSONAL SAFETY IS INVOLVED! When you see this The following safety notations are used symbol BECOME ALERT, HEED ITS throughout this manual to call attention to MESSAGE. -
Page 4: Operation And Safety Labels
Operation and Safety Labels Anchor Point Point Ancrage Bronco Floor Stripper #260P Gross Weight: 1,240 lbs. Horse Power: 17.5 Vapor Propane System Decibels: 85 dBA Nominal Width: 0.74m Length: 1.22m-1.37m Height: 1.22m Accelerateur / Tourner Pour Verrouilller Anchor Point Point Ancrage Decolleuse Bronco 94635 Vers l'avant / Arret / Inverse ˆ... -
Page 5: Safety Precautions
Safety Precautions Improper use of this machine can injure Transportation: people and damage the equipment. When hauling the machine, always use a People using or ser vicing this machine ramp that is rated for the weight of the must read and follow the instructions in machine. -
Page 6: Maintenance & Storage
Maintenance and Storage Maintenance: Keep the machine in good condition. Main- 5. While holding the box assembly, release tain it as directed in this manual and the the connector clip to disconnect the electrical motor manual for propane machines. Check wiring from the box assembly. - Page 7 Maintenance and Storage 9. The hood is now ready to be lifted forward. 4. CAUTION: use proper lifting techniques. Depress the control levers fully forward. These weights are heavy (45 to 75 lbs.) With one hand guide the levers through and should only be lifted by a person the opening, being careful not to damage that can safely lift this much weight.
- Page 8 (order part # 260P.04.22 and pre filter #260P.04.23). Use only Taylor Tools accessories, attach- ments, and replacement parts. Use of other components may void warranty. Storage:...
- Page 9 Periodic Maintenance Daily 25 hr. 50 hr. 100 hr. 200 hr. 300 hr. Check hydraulic oil level Check air filters Check engine oil level Check loose fittings Check battery electrolyte Check belt tension Clean dust from heads Change engine oil Change hydraulic oil filter Change engine oil filter Change &...
-
Page 10: Operation
Operation Before Starting Machine: Driving: 1. Check hydraulic oil level indicator and a. To move the Bronco floor stripper for- fill with Mobil DTE 25 or DTE 26 or ward or reverse, depress the control equivalent if necessary. If pumps run levers downward with the palm of your dry, permanent damage may occur. - Page 11 Operation b. To move straight for ward, push both d. Pulling the levers toward the operator levers simultaneously forward. The further will reverse the machine. The further the for ward the levers are pushed for ward, levers are pulled back, the faster the the faster the machine will travel.
- Page 12 Blade Selection: There are several blades that work well for each type of flooring material. Blades listed below are the most popular for each substrate. The Taylor Tools catalog has a lifting actuator complete list of available blades. Carpet: 265.12.SD...3 x 12 x .083" Side Cutting 266.12.SD...4 x 12 x .083"...
- Page 13 Operation d. With the wrench provided with the b. When expansion joints are identified Bronco, loosen the two bolts on the blade and marked, they should be navigated by clamp and clean any debris under the a slight angle to prevent the blade from clamp to ensure proper seating of the new engaging them at right angles.
-
Page 14: Trouble Shooting
Trouble Shooting PROPANE / ELECTRIC Problem Solution K Check to see if the bypass valves are open. Machine moves but has low power. K Check belt tension and tighten if necessary. K Check hydraulic oil level. K Check belt tension. Machine makes a loud squeal when K Check hydraulic oil level. - Page 15 Trouble Shooting PROPANE / ELECTRIC Problem Solution K Put machine on a safe block to allow free Machine moves forward or backward when control levers are in the neutral turning of the wheel to be adjusted. position. K Open machine hood (see hood opening proce- dure), and rotate the appropriate control lever clockwise or counter-clockwise until the wheel stops moving.
-
Page 16: Parts, Diagrams
Port View, Electric/Propane Catalog # Description 1 260.40.16 Jack Mount 2 260.05.32 On/Off Switch 220 Volt 3 260.05.32B Boot, On/Off Switch 220 Volt 0.02 4 260.15.22 Control Lever 5 260.40.50 Shock Absorber 6 260.60.08 Seat W/Seat Belt 7 260.60.08S Seat Belt / W Swich 8 260.70.12.KIT Filler Cap Only 9 260P.02.00... - Page 17 Catalog # Description 1 260.40.40 Blade Clamp W/ Deflector 2 260.15.31 Filter, Element, Replacement 3 260.40.02.KIT Raise/Lower Switch 4 260.40.11.KIT Fastner Kit, Blade Clamp 5 260.60.08S Seat Belt / W Swich 6 260.60.10 Foot Rest 7 260B.40.20 Transportation Wheel 8 260B.40.21 Transportation Frame, Bronco 9 260P.02.00 Key Switch, Propane Engine...
- Page 18 Catalog # Description 1 260.90.04.Kit Socket Allen Wrench Tool 2 260.05.04 V Belt 3 260.15.15 Sheave, Hydraulic Pumps 4 260.15.19 Pump, Hydraulic, Port 5 260.15.20 Pump, Hydraulic, Starboard 6 260.15.21.Kit Control Arm W/ Set Screw 7 260.15.25 Bushing, Hydraulic Pumps 8 260.15.27 Ball Joint, Control Arm 0.02...
- Page 19 Control Lever Assembly Catalog # Description Pack Wt. (lbs.) 260.15.22 Control Lever 260.15.23 Control Cables 260.15.28 Jam Nut, Cable Bracket 0.03 7&8 Catalog # Description 1 260.20.00 Hub, 2 050.20.27 1" Castle Nut NF 3 060.10.03 1/8 x 1 1/4 Cotter Pin Z 0.02 4 260.05.07 Keystock 5/16 x 1"...
-
Page 20: Warranty
Limited Warranty. Notice cannot control. The Purchaser must understand that frequent of Claim should be sent or faxed to: Taylor Tools 5045 heavy-duty use of the Product will shorten its useful life. Paris Street, Denver, CO 80239...