Takex AV-100E Instruction Manual

Thank you for purchasing a TAKEX product. Please read this Instruction Manual carefully for correct and effective use.
Please Note : This voice speaker is designed to give an message after being triggered by a PIR etc. : it is not a burglary-preventing device.
TAKEX is not responsible for damage or losses caused by accident, theft, Acts of God ( including inductive lightning ), abuse,
misuse, abnormal usage, faulty installation or improper maintenance. Regular maintenance and inspection (at least annually)
by the installer and frequent testing by the user are vital to continuous satisfactory operation of any system.
1
PARTS DESCRIPTION
Speaker
Window
Indication LED
(Built-in)
2
PRECAUTIONS
●Do not disassemble or modify this device. This may cause a fire,
electrical shock, or malfunction of the device.
●If the following events occur, turn off the power of the unit immediately,
and ask the place of purchase for repair. Failure to follow this may result
in fire, electric shock, and/or malfunction.
・Smoke, abnormal odor, and/or sound are found
・Liquid, such as water, and/or foreign material has entered the unit
・The unit has deformed and/or damaged parts
●Do not apply impact to the unit.
Strong impact may result in performance deterioration and/or damage to
the unit.
●The unit may not operate properly near devices that generate a strong
electric or magnetic field.
Also, devices near the unit may not operate properly due to the magnetic
field and/or magnetism generated from the unit.
Make sure to confirm before operation.
●Make sure to perform a sufficient operation check on the whole system
before operation.
●Sound playback time is approx. 12 secs. During playback, further input
signals does not extend the time period, or repeat playback.
●Do not splash water on to the speaker, although it is rain-proof, it is not
water-proof.
●Give careful consideration to sound volume level, especially if used at night.
4
HOW TO RECORD AND ADJUST
[ADJUSTMENT]
(Sound volume)
Adjustable between silence
to max. (100dB : 1m)
Sound volume
[RECORDING]
(1) Sensor - Remove the cover of microphone on the bottom.
(2) Turn on the power supply.
(3) While pressing the recording switch and record with keeping
10cm away sound source (mouth etc.) from the microphone.
Release the recording switch when the recording is finished.
*Record level function is also equipped with INDICATION LED.
LED blinking while recording is a right level.
(Over level : LED off, Below level : LED on)
VOICE SPEAKER
AV-100E (POWER:12VDC)
Instruction Manual
Rotary arm
Body
Rotary arm fixing bolt
Swing arm fixing bolt
Fixing screw
Swing arm
4c cord (length : 20", 0.5m)
Be sure to observe
(4) Check the recorded message by short-circuiting the input signal line.
Indication LED
(Built-in)
(5) Put the microphone cover back in place.
Microphone
Recording switch
Rubber cover
Mounting Flange
3
ANGLE ADJUSTMENT
Angle adjustment unit with
three-part rotation mechanism
as drawn right makes it to
adjust many angles.
Adjustment angles are limited
as shown in the below
diagrams.
Change to install as right figure.
30°
Install the voice speaker
●
to face downwards.
(If the message is not recorded correctly, please try to re-record.)
*Record the message in a room where there is
no noise and the wind does not blow.
*Record time is while a recording switch is
being pressed. (Max. 12 seconds.)
*Be careful so as not to press the recording
switch after recording.
If the recording switch is pressed, the previous recorded message are deleted
by overwriting
*Do not record mechanical sounds such as buzzer or siren.
It gives a load to the speaker and may cause a malfunction.
*The recorded message will not disappear even if it is stored in non-energized
state.
Self Tapping Screws
φ4×30： 4 pcs.
Adjustment
120°
Unit
▲
±180°
90°
±180°
90°
Install the window to be vertically
●
beneath the body.
Microphone