Related Manuals for Netzer DS-16
Summary of Contents for Netzer DS-16
- Page 1 ABSOLUTE POSITION ROTARY ELECTRIC ENCODER USER MANUAL DS-16 Copyright © 2020 Netzer Precision Motion Sensors Ltd. All rights reserved.
- Page 2 ABSOLUTE POSITION HARSH DS-16 ROTARY ELECTRIC ENCODER USER MANUAL ENVIRONMENT Table of Contents Preface......................... 1.1 Version: 2.0 March 2020 ................1.2 Applicable documents ..................2. ESD protection ...................... 3. Product overview ....................2-3 3.1 Overview ......................3.2 Installation flow chart ...................
-
Page 3: Esd Protection
3.1 Overview As usual for electronic circuits, during product handling do not touch electronic circuits, wires, 1.2 Applicable documents The DS-16 absolute position Electric Encoder™ connecters or sensors without suitable ESD is a revolutionary position sensor originally • DS-16 Electric Encoder Data sheet protection. - Page 4 Optional accessories: The optimal recommended amplitude values (1) DS-16-R-01 Kit, Rotor mounting shims : x10 are middle of the range according to those maylar 50um thick. shown in the Encoder Explorer software and (2) CNV-0003, RS-422 to USB converter vary according to the encoder type.
-
Page 5: Electrical Interconnection
Black Ground Power supply Setup SSI / BiSS Electric Encoder NanoMIC Connect Netzer encoder to the converter, connect the converter to the computer and run the Electric Encoder Explorer Software Tool Contents Preface ESD Protection Product Overview Unpacking Electrical interconnection... -
Page 6: Mounting Verification
ABSOLUTE POSITION HARSH DS-16 ROTARY ELECTRIC ENCODER USER MANUAL ENVIRONMENT 7. Mounting verification 7.2 Mechanical installation verification 8. Calibration (g) At the end of a successful verification, the SW will show “Correct Mechanical Mechanical Installation Verification 7.1 Starting the Encoder Explorer 8.1 Offset calibration... - Page 7 ABSOLUTE POSITION HARSH DS-16 ROTARY ELECTRIC ENCODER USER MANUAL ENVIRONMENT (b) Start the data acquisition while rotating the Offset compensated fine / Corse channel 8.2 CAA calibration shaft. The following calibration aligns the coarse/ fine channel by collecting data from each point The progress bar (c) indicates the collection of both channels.
-
Page 8: Operational Mode
ABSOLUTE POSITION HARSH DS-16 ROTARY ELECTRIC ENCODER USER MANUAL ENVIRONMENT 8.3 Setting the encoder zero point 8.4 Jitter test In case the reading data (blue dots) are not 9. Operational Mode evenly distributed on a thin circle, you may The zero position can be defined anywhere Perform a jitter test to evaluate the quality 9.1 SSi / BiSS... -
Page 9: Mechanical Drawings
WARNING Unless otherwise specified Dimensions are in: mm Do not use Loctite or other glues containing Cyanoacrylate. Surface finish: N6 Netzer recommend to use 3M glue - Scotch-Weld Epoxy Linear tolerances: ±0.1 deg Adhesive EC-2216 B/A. Contents Preface... - Page 10 WARNING Unless otherwise specified Dimensions are in: mm Do not use Loctite or other glues containing Cyanoacrylate. Surface finish: N6 Netzer recommend to use 3M glue - Scotch-Weld Epoxy Linear tolerances: ±0.1 deg Adhesive EC-2216 B/A. Contents Preface...
- Page 11 ABSOLUTE POSITION HARSH DS-16 ROTARY ELECTRIC ENCODER USER MANUAL ENVIRONMENT ICD, DS-16 cable Configuration DS-16-SE-F0 pads only Unless otherwise specified Configuration DS-16-SE-FC Dimensions are in: mm DF13-6P-1.25H connector Surface finish: N6 2.1x5 mm studs Linear tolerances: ±0.1 deg Contents Preface...
Need help?
Do you have a question about the DS-16 and is the answer not in the manual?
Questions and answers