OPCOM Farm GrowWall Quick Manual Manual

GrowWall
Thank you for purchasing OPCOM Farm GrowWall, the indoor hydroponics growth system. It is designed with easy installation
and efficient growing system in one-touch AUTO mode, up to 75 plants capacity. Read the quick guide manual carefully before
setting up. For detailed user manual and assembly video, please visit GrowWall page at www.opcom.com/growwall-support.php
.
A. Assembly
A1. Remove all parts from box and check all accessories
Grow Kit
1.Seedling Kit:
2.Nourishment:
Accessories
1. Plastic peg
6. Plastic Ties x7pc
(Backup Plastic Ties x 2pc)
Planting Accessories
Planting Basket Pack
Product Number : OAMS18K
1.Planting Basket x 100pc 2.Seedling Tray x1pc
30W LED Growth Tube (L30T) x 5 (OAEE07A)
A2. Assemble GrowWall.
Lock the matching color vertical tubes by
1
integrated fastener.
Repeat the previous action again.
2
Place the plastic peg into the round hole in
3
the bracket;affix the tube and the bracket to
the unit.And cover the top level light holder.
Attach the control box by aligning the holes.
4
Assemble water pipe and plastic tiles.
5
A3. Mount on the wall.
Place against the wall with 8.2 inches (21cm) distance.
1
Ensure air bubble in level scale is centered.
2
Mount on the wall by adhesive or screws.
3
Add 7.13 gallons (80% full) water to water tank.
4
7.13 gallons
27L
Turn on the pump for 30 mintues and ensure the water
5
flows back to the tank, please refer to user manual page 15 for cycle descriptions.
Water flow control valve: According to different plants,
6
you can adjust the water flow by water flow control valve, but you need to adjust under water.
Fuction Status Light Time(On/Off) Fuction
Auto 12H/12H
ON 24H/0H
LED High 16H/8H Pump
Low 8H/16H
OFF 0H/24H
* Most plants can de grown using the AUTO mode.
* a. When Power On, press hold POWER button until 1 beep sound (Less than 2 second) to turn off the power.
b.When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset timeline to auto power on (On/Off 16H/8H).
* a.When Power Off, press hold POWER button until 1 beep sound (Less than 2 second) to turn off the power.
b.When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset timeline to auto power off (On/Off 8H/16H).
Quick Guide Manual
Grow Sponge 2x60pk Grow Sponge 2x60pk Grow Sponge 2x60pk
(OASS001 For Green Lettuce) (OASS002 For Red Leaf Lettuce) (OASS006 For Basil)
3.pH adjusters :
NT-Starter x3pc
NT-Adjuster x15pc
pH+ x15pc
(OANT002 for GrowWall) (OANT018 for GrowWall)
x2pc 2. EC and pH Meter Set 3. pump x2pc 4. Waterproof Tape
(Backup pump x1pc）
8. Seed Moisturizing 9.Cleaning Sponge x 1pc
7. Wall Mount Brackets
Cover x 6pc
100 pcs Ø50 x 50 mm
Sponge Kit Sprout BOX x 1 pcs Sprouting Sponge x 8 pcs
Product Number : OAMS20K
3.Sprouting Sponge x 4pc 4. Lens Hood x 75pc
3 3
4
5
2 2
1 1
1
3
or
Adhesive for Screws for solid installation
flat surface (Remove R4/L4 before
(recommend).
using screws).
6
2
Ensure bubble in the center.
8.2 inch
Status Light Time(On/Off)
Auto 12 cycles/day ( 10 mins/cycle )
48 cycles/day
ON ( 15 mins/cycle )
High 4 cycles/day ( 10 mins/cycle )
Low 2 cycle/day
( 10 mins/cycle )
OFF 0 cycle/day
☑
Please read and follow every steps to avoid any malfunction.
B. Planting
B1. Sowing Stage
Refer to below table for sponge quantity and planting numbers.
1
Plant Size
Sponge Number
Planting Number
How to Set up
2. First time sprout: just open the seedling box and add water. Then go to step 5. (Fig 1)
2
Add water to the seedling tray, up to the water level. (red)(Fig1)
3
Second time sprout:Open Grow Sponge package, put the sponges into water of seedling tray,
4
press the sponges into water 5 seconds and ensure the sponges absorb water completely.(Fig2)
Grow Sponge 4x60pk (OASP001)
Place the seedling tray with cover in the shade or cover it with black cloth(to block light).(Fig3)
5
Spray water and keep the sponges wet every day.(Fig4)
6
During 0-7 days(leaf plant), find the sprouted ones in the tray; pick them out, and move them into
7
pH- x15pc growing hole and keep the remaining seedlings.
Discard unsprouted sponges after regular germination time.
8
Different plant may have different germination time, please check before plant.
9
Chart II: Plant Stage
Basil, Lemon Balm
5. Expansion Anchor Bolts x4pc
Wall-Mount Screws x 4pc
Sprout Stage
Young Plant Stage
Growing Stage
10. Water Spray 100ml x1pc
* Please keep the seeds in refrigerator if you don't use it, recommended temperture is 41℉
* For your expected plant amout, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist www.opcomfarm.com and read "Plant Q&A".
Manual
B2. Seedling Stage
When the germination rate exceeds 70%, move to the seedling stage, discard excess sponges.
1
Move all sponge to the grow tube and set up in balance depending on plant size.
2
Warranty Card Quick Guide Manual
In each sponge, keep strong plants and cut the other weak plants.
3
Add 1 starter nutrient to the water tank and ensure EC between 1000-2000μS/cm
4
(=1.0-2.0 ms/cm).
Ensure pH between 5.5-6.5 (adjust by pH capsule).
5
Adjust LED lights and keep around 2 inches distance to cover all the plants.
6
* For EC & pH adjustment instructions, please refer to user manual pages 28-29.
B3. Growing Stage
When young plants grow to over 2 inches height, change control box to AUTO mode.
1
B4. Grow to Harvest
Water Pipe Plastic Tiles After 4-6 weeks, harvest larger plants for consumption.
1
Reserve smaller plants to grow.
2
* To save time, sow the new seeds in sprout box for the next planting cycle before a week of harvesting.
C. Optional
C1. Regrowing
OPCOM Farm is designed with a special re-grow process to maximize harvest capacity for family consumption. First harvest
cycle takes 3-4 weeks after seeding young plant is planted. During harvesting, cut out the larger leaves and allow the smaller
ones to continue to grow in the machine. After the first harvest, you can continue the harvesting method weekly for the next
3-4 weeks without the need to re-seed.
C2. Sprout Process
GrowWall is not only a hydroponics system but also a Sprout Machine with our free gift, sprout box. Within one Hydroponics cycl e time, you can
have 3-4 sprout harvests and each harvest cycle is 7-10 days. Enjoy your maximum planting capacity. Refer to user manual pages 24-25 for details.
Day 0
Put seeds in warm
water for 24 hours .
Please visit OPCOM farm website at www.opcom.com/growwall-support.php for complete information, including user manual,
Planting Q&A, videos and updates.
Small Plant Size Medium-Large
105 Sponge Number 60
75 Planting Number 40
How to Set up
T (℉)
Planting Time LED Mode Pump Mode Nourishment
Day 0~7 N/A N/A N/A 68℉- 77℉
Day 3~14 ON ON NT-Starter 59℉- 86℉
After Day 14 Auto Auto NT-Adjuster
59℉- 86℉
5 0℉.
-
3-4 weeks (15 plants / tube)
Day 1
Spread the seeds on
fully wet sprout sponge.
Put sprout box on top of water tank and
also insert the water tube into box.
(Fig1）
This side up!
(Fig2）
(Fig3)
(Fig4)
RH EC pH Notes
Ensure each sponge is fully wet in
80% 0.5-1.0 5.5-6.5
seedling tray.
45%-70% 1.0-2.0 5.5-6.5
45%-70% 1.0-2.0 5.5-6.5
Up to135°
13 inch
2 inch
3-4 inch
5-6 weeks (8 plants / tube)
Day 7-10
Open top cover for green sprout.
Cover for no edible green parts.