Advertisement
Quick Links
Advertisement
Summary of Contents for iBells DS 80-70
- Page 1 DRYWALL SANDER DS80-70|90...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. GENERAL POWER TOOL SAFETY WARNINGS __________ 2. DRYWALL SANDER SAFETY WARNINGS________________ 3. PRODUCT OVERVIEW _________________________________ 4. PRODUCT SPECIFICATIONS ___________________________ 5. SETUP _________________________________________________ 6. PRODUCT FUNCTIONS AND ASSEMBLY________________ 7. GENERAL OPERATION ________________________________ 8. TROUBLESHOOTING __________________________________ IBL DS80-70|90... -
Page 4: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings, instructions, WARNING! illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool WORK AREA SAFETY... - Page 5 PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs or alcohol. A moment of inattention while operating power tools may result in serious personal injury.
- Page 6 POWER TOOL USE AND CARE Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off.
-
Page 7: Drywall Sander Safety Warnings
DRYWALL SANDER SAFETY WARNINGS Misuse or failure to follow the safety rules stated in WARNING! this instruction manual may cause serious personal injury. This power tool is intended for sanding drywall for home use only. Using this tool for professional purposes will reduce the tool’s lifespan and cause parts to wear down sooner. - Page 8 Position the power supply cord out of rotating accessory. Do not abuse the cord, never use the cord to carry the tools or pull the plug from the outlet. Always make sure that any extension cord you use is in good condition, and if used outdoors is of a suitable type, and so labelled.
-
Page 9: Product Overview
PRODUCT OVERVIEW IBL DS80-90 Adjustable edge guard 5. Dust Extraction Control 1. ON/OFF Trigger Switch 6. Dust Port 2. Switch Lock ON Button 7. Guard-Sanding base 3. Variable Speed Control 8. LED Light Switch 4. Auxiliary Handle IBL DS80-70|90... - Page 10 IBL DS80-70 5. Dust Extraction Control 1. ON/OFF Trigger Switch 2. Switch Lock ON Button 6. Dust Port 3. Variable Speed Control 7. Guard-Sanding base 8. LED Light Switch 4. Auxiliary Handle IBL DS80-70|90...
-
Page 11: Product Specifications
ACCESSORIES P240 Sanding Discs (x 2) Carry Strap Dust Bag Dust Extraction Hose Clasp (plastic slide fastener) PRODUCT SPECIFICATIONS Rated voltage : 230V~50Hz Rated Input Power : 800W Rated no load speed : 1200-2300 rpm Wheel/Pad diameter : 180 mm Sanding disc diameter : 190 mm Dust port diameter... -
Page 12: Setup
INTENDED USE The Drywall sander is a hand-held power tool suitable for sanding plastered walls, ceilings, and interior walls, as well as for removing paper residues, paint layers, coatings, adhesive residues, and loose plaster. The device can also be used to sand the floor as well. -
Page 13: Product Functions And Assembly
PRODUCT FUNCTIONS AND ASSEMBLY ON/OFF SWITCH AND LOCK-ON BUTTON Switch the device ON by pressing the ON/OFF switch (1) and OFF by releasing the switch. It is also a variable speed switch that delivers higher speed and torque with higher pressure. For continuous operation, Press the switch then lock-on button (2), release switch first, then lock-on button. - Page 14 AUXILIARY HANDLE An auxiliary handle (4) is supplied with the product and can be fixed to the left or right hand side according to the operators convenience. This handle should be used all the time to maintain complete control of the tool. SANDING DISC Place the new abrasive disc accurately onto the backing pad on the guard (7).
- Page 15 DUST EXTRACTION AND REMOVAL FITTING THE DUST BAG AND HOSE: The dust hose and dust bag available with the product allow the dust to be captured for easy clean up and should be fitted to help maintain a clean, healthy working environment.
-
Page 16: General Operation
GENERAL OPERATION Do not force the tool or apply excessive pressure, WARNING! this may cause damage to the motor. Let the tool do the work. Always use the side handle. The operator should adopt a comfortable posture with their feet apart and firmly balanced. ... - Page 17 CLEANING AND STORAGE Tool should be kept clean, especially its air vents. Keep the tool and ventilation slots (air vents) clean and free from obstructions. Accumulation of dust in the motor or on the base may cause a malfunction of the tool. ...
- Page 18 CARBON BRUSH INSPECTION AND REPLACEMENT: The wear on the carbon brushes depends on how frequently and how heavily the tool is used. If you see excessive sparks during operation or if the tool stops working, inspect the brushes and replace them. ...
-
Page 19: Troubleshooting
TROUBLESHOOTING Suspected malfunctions are often due to causes that the users can fix themselves, therefore check the product using this section. In most cases the problem can be solved quickly. Problem Possible Cause Solution 1.1 Wire in the main 1.1 Have the socket and plug or in the plug checked by a socket is loose. - Page 20 Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. Do not dispose this product by normal household waste, but take it to a collection point and recycling of electrical and electronic equipment.