Summary of Contents for Aerial MURA PSGC
- Page 1 MURA Release Kit (PSGC) November 2013 Aerial Machine and Tool Corp. www.aerialmachineandtool.com 4298 JEB Stuart Hwy Phone: 276-952-2006 Meadows of Dan, VA 24120 FAX: 276-952-2231...
-
Page 2: Table Of Contents
This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent in writing from Aerial Machine and Tool Corp. -
Page 3: Introduction
KEEP YOUR VEST AND RELEASE SYSTEM IN USABLE CONDITION. IMPROPER WEAR MAY RESULT IN DAMAGE TO THE COLLAR. DO NOT WEAR ANY GARMENT OR PIECE OF EQUIPMENT OVER THE RELEASE. IMPROPER USE OR NEGLIGENT CARE THIS EQUIPMENT CAUSE SERIOUS INJURY DEATH. Aerial Machine and Tool Corp. Page 3... -
Page 4: Preflight Inspection
If part of the thread on the back stitch has come loose, this is not cause for rejection. Trim any loose back stitch threads to keep the stitch from unraveling. Aerial Machine and Tool Corp. Page 4... -
Page 5: Cleaning
The MURA may be cleaned using the following methods: • The fabric and webbing may be wiped or sponged using soap solution or household detergent to remove light soil. • The quick release may be cleaned by washing with a stream of water. • Sand, dust, and other debris may be removed from the webbing, fabric, and quick re- lease using compressed air or soft brushes. Wear eye protection while using compressed air to remove debris. Aerial Machine and Tool Corp. Page 5... -
Page 6: Assembly (Platform)
Snaps should be to the top. The platform is used to stabilize the handle when flotation collar is also attached.. The platform is not needed if using the MURA without a flotation collar. The platform can be attached to either side of the vest depending on handle placement 5.1 Platform mounting Aerial Machine and Tool Corp. Page 6... -
Page 7: Assembly (Quick Release)
Install pins on a smooth hard surface to avoid damaging the clevis arms. The pins should be pressed into the quick release completely Grooved pins are one time use only! DO NOT REUSE 6.1 Assembly of MURA to loop Aerial Machine and Tool Corp. Page 7... - Page 8 6.2. Route cable down the back of the vest forming a loop. The loop should extend through the webbing on the back of the harness as shown below. 6.2 Routing of MURA cable through webbing Aerial Machine and Tool Corp. Page 8...
- Page 9 MURA Release Kit - User’s Manual 6.3. Attach Web Dominators in three suggested locations as shown. The Web Dominators can be moved to accommodate the placement of other equipment. 6.3 Attachment and recommened location of Web Dominators Aerial Machine and Tool Corp. Page 9...
- Page 10 Web Dominators are recommended. Web Dominators can be subsituted with a heavy duty cord (ie. 6 cord). Ensure the cable moves freely. 6.4 Attachment of cable to Web Dominator Aerial Machine and Tool Corp. Page 10...
- Page 11 6.5. Pull the quick release to the end of the loop and form a wrap with the Velcro provided. This will keep the quick release in position at the end of the loop. The wrap is optional, but recommended 6.5 Optional Velcro wrap Aerial Machine and Tool Corp. Page 11...
-
Page 12: Assembly (Handle)
MURA Release Kit - User’s Manual 7. Assembly (Handle) 7.1. Lay the handle out on a flat surface. 7.1 Release handle 7.2 Insert metal tab completely into lower pocket. 7.2 Metal tab into pocket Aerial Machine and Tool Corp. Page 12... - Page 13 7.3 Snap the handle to the pocket 7.4 Form a loop on the upper portion of the handle 7.3 Handle snap 7.4 Form loop 7.5 Carefully insert the loop into the upper pocket 7.5 Loop into upper pocket Aerial Machine and Tool Corp. Page 13...
- Page 14 MURA Release Kit - User’s Manual 7.6 Fold cover over to protect assembly 7.6 Handle cover Aerial Machine and Tool Corp. Page 14...
- Page 15 MURA Release Kit - User’s Manual 7.7 Attach the MOLLE handle to the outside of the platform. The flotation will be attached to the inside. (If flotation is used) with platform without platform 7.7 Handle attached Aerial Machine and Tool Corp. Page 15...
-
Page 16: Operation
8.1 Grab Handle Lift up to release snap Lift up to release tab Pull down to activate quick release Aerial Machine and Tool Corp. Page 16... -
Page 17: Parts List
* * U niversal C amo = U C M ulti C am = O CP Aerial Machine and Tool Corp. -
Page 18: Additional Photos For Reference
MURA Release Kit - User’s Manual Aerial Machine and Tool Corp. Page 18... - Page 19 MURA Release Kit - User’s Manual Aerial Machine and Tool Corp. Page 19...
- Page 20 MURA Release Kit - User’s Manual Aerial Machine and Tool Corp. Page 20...
Need help?
Do you have a question about the MURA PSGC and is the answer not in the manual?
Questions and answers