B&PLUS RCS Series User Manual

Remote System
User's Guide
Remote Power supply system
210W specification RCS series
Charging unit : RCS210-PB24
Power Supply unit : RCS240-AC1
Passive Head : RCS240PH
Active Head : RCS240AH
Attention for Installation
(Read this section thoroughly before installation.)
Before using the Remote Sensor, read this manual carefully.
During installation and operation, pay close attention to the
safety aspect.
◆ Please turn off the Remote System before any performances
such as mounting, maintenance or breakdown.
◆ Ensure correct connections by reference to the wiring dia-
gram.
◆ To avoid malfunction caused by induction noise, cable
should be kept apart from motor or other power cable.
◆ Work for a while or immediately after operation, please do
not touch the (power supply unit, charging Unit, Head part) hot
spots. Doing so could result in burns.
◆ This product, which is one of those high frequency utiliza-
tion equipment of Radio Law, Upon use You will need to install
application. Please use it after you have made the application
without fail. Installation details of the application procedure,
see Telecommunications website of the Ministry of Internal
Affairs and Communications, Please.
◆ This product has become a Japan national specification. It
can not be used outside of Japan. It can not be used outside
of japan. When used outside of Japan, I guess we assume any
liability You.
Dimension
[Charging unit] RCS210-PB24
Specification
Charging unit
Type code RCS210-PB24
Rated input voltage −
Output voltage / current Max30V / Max7A
Current consumption −
Operating / Storage temperature 0 〜 40℃ /0 〜 50℃
Protection class IP20
C o n n e c - Power supply / signal Round 3 pin / Round 5 pin
tion Power −
Terminal block Battery connection(2-pole),Thermistor connection (2-pole),
Terminal width is 6.2 mm or less,Terminal screw size is M3.
Various signal connector Refer to the following page "wiring."
Cooling method Natural air cooling
Protection circuit Input overvoltage protection
Battery high temperature / low temperature protection
Battery not connected protection
Battery reverse connection protection
Accessories Output cable (1.5m), Thermistor with cable (1.5m),
External device communication connector, 4 screws M6x15
Parallel driving None
Series driving Avaiable
Signal output time required Up in zone signal light from entering the head transmission area ≦ 5s
To start charging from the in-zone signal lights ≦ 5s
2017. 07. 26 T313402He
System configuration
【Head】
Temperature control
[Thermistor]
RCS240PH RCS240AH
24V AC Power
【Power
lead battery
【Charging unit】
Supply unit】
External
RCS210- External
RCS240-
control
control
PB24
AC1
devices devices
Power supply
(Wireless Power Supply)
Various signal transmission
Signal transmission Various signal transmission
【Function of each component】
Power supply unit : I will convert to the high-frequency power supply, the
AC power. Further, in response to the (power supply start signal) input
signals, supplies a high frequency power to the Active head, and
output control equipment in Zone signal and various signals Active
head is received.
Charging unit : And is Charging to the battery. It regularly monitors the
battery voltage and output voltage [battery monitor signal H, M, L] as
the result.
Head : I can carry a variety of signal and power transmission in a
non-contact.
※ Each cable, please
【Connection diagram】
connect with the specified
Output cable
length.
You may receive an error
(1) 24V lead battery due to the output such as a
decrease occurs.
Please refer to the
[Mounting of the ferrite
(2)
clamp]of the rear surface.
Thermistor with Cable
Charging unit Power Supply unit
(1) (1)
External
External device
device com-
communication
Power
munication
cable
cable
cable
(AWG24 〜 16)
(AWG28
〜 16)
Passive
Active Head
Head
(1)Parts of the dotted line (External device communication cable
and 24V lead batteries) within the product is not included with this
product. They are contents prepared and processed of a visitor.
(2)I have you use the attached article always, please paste it into
the top portion of the terminal near the 24V lead battery thermis-
tor. In the case,please do not touch any terminals.
[Power Supply unit] RCS240-AC1
300
15 90 90 90 15
8-7X15
Power Supply unit
RCS240-AC1
AC100V / AC200V
−
4A
0 〜 50℃ /0 〜 50℃
IP20
Round 3 pin / D-sub 9-pin
3P inlet
−
Refer to the following page wiring.
Forced air cooling
−
Power cable (2m), External device communication
connector, 4 screws M6x15, One ferrite clamp
Dimension
[Passive Head]
RCS240PH
Specification
Type code
Application charging unit / power supply unit
Rated gap Distance
Center offset
Operating / Storage temperature
Protection class
Connection Supply
(With the connector
cable 1m)
Signal
Accessories
Wiring
● Charging side (RCS210-PB24)
① The output terminal for batteries
② The terminal for thermistor
③ Input signal (voltage monitor request signal)
Other than at the time of charging, It is used when you want to output the batteries voltage monitor request signal.
Charging unit
Internal circuit
④ Output signal
Each output signal is open-collector. The maximum current value and the maximum output voltage, please connect so
as not to exceed the maximum value by referring to the following values .
Connect the load before doing so, please do not short-circuit the output signal.
80
1
〇 +
Charging unit
Internal circuit
〇−
<Input signal pin assignment>
Signal type
Input Voltage monitor request
O u t - Voltage monitor signal H
Voltage monitor signal M
put
Voltage monitor signal L
Float charging signal
charging signal
Error signal
[Active Head]
RCS240AH
Passive Head Active Head
RCS240PH RCS240AH
RCS210-PB24 RCS240-AC1
10mm
The sum total of gap of length and width is 10 mm or less.
0 〜 50℃ /-10℃〜 50℃
IP65
Connected to the Charging unit at the (fe- Connected to the Charging unit at the (male)
male) 3-pin round
3-pin round
Connected to the Charging unit at the (female) Connected to the Charging unit at the
5-pin round (male) D-sub9 pin
4 screws M6x15, One ferrite clamp
1234567891011121314
③
① ②
+
● Input current : 100mA
Vin
● Input voltage : 7.5V 〜 30V
7.5 〜 30V
−
Ｉ Vcc
● Maximum load current : 5mA
Load
● Maximum load voltage: 24V
To fit each condition,
please select the load
1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ −
H + H - M + M - L + L - F + F -
Pin Contents
number
1.2 It monitors the battery voltage and the voltage applied to this pin, and the output
voltage monitor signal.
3.4 It is almost fully charged. (Charging aim:about 90%)
5.6 If the charge has been reduced somewhat. (Charging aim:about 70%)
7.8 It needs charging for charging amount is reduced. (Charging aim:less than about 50%)
9.10 It turns on, when a charging current value turns into a rated value.
11.12 I will turn OFF during charging ON, in charge cut-off and float charging start.
13.14 It turns on, if a battery error occurs.
Wireless Power Supply by
(Former NIHON BALLUFF co., Ltd.)
Mail ：b-plus-usa@b-plus-kk.com Web：http://www.b-plus-kk.com
④
C + C - N + N -