Advertisement
Quick Links
50545-555
Glider Bracket Pack
Parts
4 14186-400
Glider Bracket
50395-705 Hardware, Glider Fasteners
8 12002-207
Flat Washer, 3/8"
4 12017-207
Lock Washer, 3/8"
4 17003-1413 Hex Bolt, 3/8 x 3-1/2"
4 17003-1813 Hex Bolt, 3/8 x 4-1/2"
4 12052-107
Nylock Nut, 3/8"
8 12002-206
Flat Washer, 5/16"
8 17036-602
Lag Screw, 5/16 x 1-1/2"
Lock Washer 3/8"
Flat Washer 3/8"
Hex Bolt 3/8 x 3-1/2"
Hex Bolt 3/8 x 4-1/2"
Remove Bolts
This package is for use with Premium Pine and
Classic Pine swing beams. The Premium Pine
Lock Nut 3/8"
Lag Screw 5/16 x 1-1/2"
Glider Brackets
beam is shown in the illustrations.
Flat Washer 5/16"
steP ONe – Prepare for installation
If this is a new installation, do not install the pair
of Swing Hangers closest to the Legs of the
Swing Beam. If the Swing Hangers are already
installed, remove them.
Find the two pair of Bolts above the Swing
Hanger positions nearest the Legs. Remove
the four Hex Bolts and associated washers and
weld nuts.
Glider Brackets
See instruction for the gym
to which the Swing Beam is
mounted for special safety
information regarding required
space, resilient ground cover,
etc.
all hardware on this set
is specially coated for
corrosion resistance.
if non-creative Playthings
hardware is used, it must
be galvanized or stainless
steel.
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Creative Playthings 50545-555
- Page 1 50545-555 Glider Brackets Glider Bracket Pack This package is for use with Premium Pine and Parts Classic Pine swing beams. The Premium Pine beam is shown in the illustrations. 4 14186-400 Glider Bracket 50395-705 Hardware, Glider Fasteners 8 12002-207 Flat Washer, 3/8" 4 12017-207 Lock Washer, 3/8" 4 17003-1413 Hex Bolt, 3/8 x 3-1/2" 4 17003-1813 Hex Bolt, 3/8 x 4-1/2" 4 12052-107 Nylock Nut, 3/8" 8 12002-206 Flat Washer, 5/16" Glider Brackets 8 17036-602 Lag Screw, 5/16 x 1-1/2" See instruction for the gym to which the Swing Beam is mounted for special safety information regarding required Lock Washer 3/8" Lock Nut 3/8"...
- Page 2 assemBlY iNstructiONs steP tWO - drill Holes On one side of the beam, align the top holes Drill 3/16" of a Glider Bracket with two of the holes where Bolts were removed in the previous Dia. Holes step. Mark the position of the lower holes of the Glider Bracket on the Beam. Do the same with another Glider Bracket and the other pair of holes. Drill 3/16" diameter holes 1-1/2" into the Beam at the marks. Turn the Beam over. Mark and drill the beam in the same manner. steP tHree - Fasten Glider Brackets Fasten the Gliders Brackets to the Beam As- sembly using two 3/8 x 4-1/2" Hex Bolts*, four 3/8 Flat Washers, and two Nylock Nuts for each pair of Brackets, in the upper holes as shown. Use one 5/16 x 1-1/2" Lag Screw...
Need help?
Do you have a question about the 50545-555 and is the answer not in the manual?
Questions and answers