Astrel MICROSPA Installation And User Manual

Table of Contents

Quick Links

Download this manual

MICROSPA controller - Installation and user manual

1. General warnings..........................................................................................................2

2. Responsibility of the user .............................................................................................2

3. Accessing the live parts ................................................................................................2

4. Precautions when handling the board...........................................................................2

5. Installation tips .............................................................................................................3

6. Disposal and cleaning...................................................................................................3

7. Connection to the power supply ...................................................................................3

8. Connecting the 230 VAC loads....................................................................................3

9. Connecting the light......................................................................................................3

10. Starting for the first time ..............................................................................................4

11. Main functions..............................................................................................................4

12. Low Level Programming..............................................................................................6

13. Error Messages .............................................................................................................6

D:\LAVORO\CONTROLLI SPAS\MANUALI INSTALLAZIONE\MICROSPA\Instruction Microspa.doc

Astrel S.p.A.

Via Isonzo, 21/E - 34070 Mossa (GO) Italy

Tel. (+39) 0481 637301 r.a.-Fax (+39) 0481 637362

e-mail: info@astrel.it - www.astrel.it

Cap. Soc. € 619200. i.v.

Tribunale di Gorizia n. 3505

R.E.A. n. 049936 - M/351122

Part. IVA e Cod. Fisc. 00187070313

Sheet 1/7

Table of Contents

Need help?

Do you have a question about the MICROSPA and is the answer not in the manual?

Questions and answers

Summary of Contents for Astrel MICROSPA

Page 1 Tel. (+39) 0481 637301 r.a.-Fax (+39) 0481 637362 R.E.A. n. 049936 – M/351122 e-mail: info@astrel.it – www.astrel.it Part. IVA e Cod. Fisc. 00187070313 MICROSPA controller - Installation and user manual 1. General warnings......................2 2. Responsibility of the user .....................2 3. Accessing the live parts ....................2 4.
Page 2 MSPA controller to the minipool. This manual is an integral part of the product and therefore must be kept for future reference. Astrel S.p.A. reserves the right to make any modifications it considers necessary without prior warning or replacement.
Page 3 The power cable should be connected to the main power supply. The MICROSPA controller can be connected of power supply: Single-phase: 230 V, 50/60Hz, 15 A 8. Connecting the 230 VAC loads The loads operating at mains voltage (230 VAC) must be connected to the controller using the jacks.
Page 4 If the light is not turned off stopped manually, it stops automatically after 20 minutes of operation. • Controlling the water temperature (Up/Down arrow) The MICROSPA controller can control water temperature in a range of temperatures between 15 and 40° C. The user can set the desired temperature from keypads using on the UP/DOWN key.
Page 5 – www.astrel.it Part. IVA e Cod. Fisc. 00187070313 The MICROSPA controller maintains the temperature within an interval of ± 0.5° C around the desired temperature. When the heater is activated, the corresponding led on the keypad is on steady. The same led blinking when the water needs to be heated, but the heater is not activated to limit the power input.
Page 6 It is possible to configure various systems operating parameters from the keypad. This is normally done at Astrel factory or by the spa manufacturer, but may be done at anytime. The configuration will be kept into an EEPROM memory. To program these system parameters, the Light key must be held for 20 seconds.
Page 7 Turns the heater, pumps, blower & light off when water temperature reaches 44.4ºC. All keys that start accessories are disabled. Until the water temperature cools to 43ºC. The display blinking • Power-up detection The display blinking after a power failure until a key is pressed D:\LAVORO\CONTROLLI SPAS\MANUALI INSTALLAZIONE\MICROSPA\Instruction Microspa.doc Sheet 7/7...