Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for EyeView Gpower-S3PIR
- Page 1 IP Speed Dome Hardware Installation Guide Ver. 070906...
-
Page 2: Table Of Contents
Table of Contents INTRODUCTION..................... 1-1 Package Contents ....................1-1 Features and Benefits..................1-2 Safety precautions ....................1-3 Warning indications for use ................1-3 Environmental requirements ................1-3 Precautions on installation ................. 1-4 H/W Installation Procedure ................2-6 Connections ......................2-6 2.1.1 Indoor connections ......................2-6 2.1.2... -
Page 3: Introduction
INTRODUCTION 1.1 Package Contents Indoor Outdoor Power Core (for Indoor) Software CD Adapter (for Indoor) Power Box (for Outdoor) -
Page 4: Features And Benefits
1.2 Features and Benefits MPEG-4 compression gives a high resolution image quality The IP speed dome offers an optimal combination of network, digital, and optical technology. The IP Speed Dome adopts MPEG-4 ASP compliant compression technology which compress video analog into video streaming while maintaining resolution up to full-D1, 30 fps. -
Page 5: Safety Precautions
1.3 Safety precautions Select a proper location and use safe hoist for installing speed dome cameras. Confirm that the hoist is capable of lifting to the installation position. Proper protective measures must be provided in the hoist, for protecting engineering staffs. Confirm that power supply is 110V/220V. -
Page 6: Precautions On Installation
1.6 Precautions on installation Basic requirements for installation Follow local regulations about installation safety request. Check out if accessories are complete. Optional accessories are required for different installation sites. Please contact your local distributors for proper installation accessories, so that the camera could be installed safely without causing danger. - Page 7 This product is normally installed in an elevated position. Installation work should comply with local safe regulations. Proper safety precautions and protective measures shall be taken for installing the camera. 10. For the personnel safety sake, carry out electrification and product test only after completion of installation work.
-
Page 8: W Installation Procedure
H/W Installation Procedure 2.1 Connections Indoor IP speed dome connection is different from the outdoor IP speed dome. Follow the description below to connect to respective apparatus. 2.1.1 Indoor connections 1. Video-out cable Connect it to the video-in port of respective apparatus. The signal is 75Ω Composite Video Signal. -
Page 9: Outdoor Connections
2.1.2 Outdoor connections Power Input - Wire Connection needed 1. Power input Connect this jack to the power supply of 110VAC or 230VAC according to the product you bought. 2. RJ45 Cable Connection Connect the RJ45 port from housing cable to another RJ45 network cable for LAN/WAN inside the power box. -
Page 10: Speed Dome Set Up
2.2 Speed dome set up Follow the description below setup IP speed dome’s hardware camera ID, baud rate and protocol. AP (NVR2) setup Video platform setup Speed dome setup Camera ID, baud rate and protocol setting in these 3 item should be the same for PTZ control function to work. - Page 11 ● Protocol and baud rate switch SW10 PELCO D-2400 PELCO P-4800 PELCO P-9600 EYEVIEW (Recommended) ● Camera ID address setting Please refer to the Appendix. A “Camera hardware ID setup”...
-
Page 12: Indoor H/W Installation Procedures
2.3 Indoor H/W Installation Procedures 2.3.1 Indoor installation Installing the camera: Take out the camera upper casing, as shown below: Wall mount Pandent mount Wiring After completion of the above works, connect the wires for video / DC15 V Power Input/ LAN/WAN. Electrification test Before connecting the power, make a final check to confirm correct wiring. -
Page 13: Outdoor H/W Installation Procedures
2.4 Outdoor H/W Installation Procedures There are 4 kinds of outdoor application. And each of them requires two steps to install the outdoor IP speed dome. Please refer to the picture below to understand each application type. Then follow the procedure below to install it. 2.4.1 Understand Outdoor applications Outdoor Wall mount... -
Page 14: Install The Mount
Outdoor Corner mount Outdoor Housing outdoor Wall mount outdoor Corner bracket Outdoor Pole mount Outdoor Housing outdoor Wall mount outdoor Pole bracket 2.4.2 Install the mount The mounting wall must be strong enough for holding the camera. Minimum loading capacity should be at least 35 kg or above, for prevention of fall and personal injury. - Page 15 shown below: 170mm 200mm 114mm 140mm Drill 4 holes Ø 6.5mm: Use the 4 screws provided to fix the mount on the wall 2-13...
-
Page 16: Connect The Housing To The Mount
2.4.3 Connect the housing to the mount Insert the cable from the housing through the hole. There’s some lubricating oil inside the tube, thus the cable would have some oil on it once inserted through the Tube. Then take out M6 screws and hexagonal wrench provided within the package and fasten the 4 screws as pictue below. - Page 17 Connect the housing cable to the board in the junction box Connect the junction box to respective apparatus. Please refer to Page 2-17 for how to connect. 2-15...
-
Page 18: Detailed Dimensions
2.5 Detailed dimensions 2.5.1 Outdoor Housing 2-16... -
Page 19: Outdoor Wall Mount
2.5.2 Outdoor Wall mount 2-17... -
Page 20: Outdoor Ceiling Mount
2.5.3 Outdoor Ceiling mount 2-18... -
Page 21: Outdoor Corner Mount
2.5.4 Outdoor Corner mount 3/4" PT 2-19... -
Page 22: Outdoor Pole Mount
2.5.5 Outdoor Pole mount These four holes are symmetrical to each 2-20... -
Page 23: Appendix
Appendix 3.1 Camera ID Sep up Symbol “○” in the following tables denote setting “ON” 1 2 3 4 5 6 7 8 3-21... - Page 24 1 2 3 4 5 6 7 8 3-22...
- Page 25 1 2 3 4 5 6 7 8 3-23...
- Page 26 1 2 3 4 5 6 7 8 3-24...
- Page 27 1 2 3 4 5 6 7 8 3-25...
Need help?
Do you have a question about the Gpower-S3PIR and is the answer not in the manual?
Questions and answers